Jump to content
SAU Community

R32 GXi Clutch Kit

alienracer
 Share

Recommended Posts

alienracer Apprentice

alienracer

Posted
Posted

Just joined your GREAT!! website. Very imfortative and loads of fun.

Here is my first post. I have a R32 GXi Sedan and I am looking for a clutch kit. The engine is the ca18i, 1800cc, n/a. I was wondering if anyone could help me with any brand clutch kits that would work with this setup, and if you could suggest any race clutches.

Heard that race clutches are better suited for wear and tear, and much tolerable than the OEM clutch kit.

Your help is appreciated

Link to comment
https://www.sau.com.au/forums/topic/62225-r32-gxi-clutch-kit/
Share on other sites
Ant Collaborator

Ant

Posted
Posted
R32 Sedan with a CA18??? is this stock?

umm... I am thinking about putting in a stock GTST clutch, imo that is more than adequate for

an NA Car...  

BTW - post photos of your car.. I am curious.

Yep, GXi is the lowest spec R32, came standard with the CA18. There are a few of them running round in NZ. Must be a heap of empty space under the bonnet!

alienracer Apprentice

alienracer

Posted
  • Author
Posted

Yup there is a heap of space in the engine bay. That is the motivation to upgrade the motor when the cash makes itself available. It's not a performance engine but it's alot of fun if you are into messing around in a car park.

The chassis plate has the code for the GTS 5 spd gearbox on it. So I guess the GTST clutch should work without any problems.

I was talking to a guy who owns an R32, with much better engine, and he was telling me that any clutch assembly should fit the R32. Just wondering how true this statement is, especially when it comes to my baby with her lil 1800cc knocker.

Have to ask a silly question. Does anyone know the size of the pressure plate and clutch disc, dimensions that is?

alienracer Apprentice

alienracer

Posted
  • Author
Posted

Ok I did some research and found out that the S13 has the same gearbox as the GXI R32 skyline. The gearbox is the one from the GTS model (FS5W71C). I have no experience with purchasing a clutch kit. I know I do need the full kit (pressure plate, release bearing, and clutch disc) cause my clutch is slipping like a "you know what".

The car is RWD, does this mean I have to get a special clutch ? The service manual calls for a 225mm clutch disc, but I am not sure about the teeth on the shaft and the clutch disc.

Was checking ACT website and came across a clutch which I thought might work. Anyone shed some light on my predicament.

ACT Clutch

alienracer Apprentice

alienracer

Posted
  • Author
Posted
May i ask why you are wasting your money on this car? it is pointless. save some money and sell your car and getyourself a R32 89 GTS ATLEAST!

Cheers

Thanks for your opinion. Until I can get the cash and sell this car I still need something to drive around, :rant:.

Back on topic, does anyone know how many teeth are on the clutch disc shaft?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...