Jump to content
SAU Community

Recommended Posts

Bushes sit between moving metal parts. They can help absorb shock as well as the prevention of wearing of metal parts. Different bushes have different hardness - usually stock ones are on the soft side to give driver comfort and realistically aren't designed for agressive driving. Upgrading to poly bushes or similar can make a noticeable difference to the firmness of handling and IMHO are a worthwhile upgrade.

Steve

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-95219
Share on other sites

FYI

I just called a whiteline distrubutor here in vic, and I got some prices for polyeurathane bushed for an R33

Front control arm uppers: $145

Strut to chassis (front): $107 ($63 for standard)

Rear control arm upper: $??? (no price)

Rear sway bar mount to chassis: $14.44

these guys are in 28 Ovata drive, Tullumarine

ph: 9330 1166

I'm getting a squeek from the front in the mornings when the car is cold. I dont suppose any1 has had the same, and changed their bushes. Its just that I haven't looked at them yet, but i was sondering which of the 2 it is likely to be...

Zahos

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-95386
Share on other sites

inark:

Pineapple rings are used for one of 3 different applications. They can be set up for drag (increased rear squat on launch), drift (opposite of drag) or general performance (in between). They also help reduce axle tramp.

Zahos:

Sorry I didn't mention this before, whiteline also do 'handling' kits - buy as a kit and save a few bucks - may be worth a look.

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-95395
Share on other sites

  • 2 weeks later...

I have a '95 R33 GTS-T and it has after-market suspension, when i drive on some bumpy roads i get rattles (i think only from the rear), i always thought it was just the jack or something in the boot moving around but the previous owner said i need to get "bushes" coz its metal on metal and thats the sacrifice u make for having good suspension.

How do i know what set of bushes i need ? there are like 243 different products on www.whiteline.com.au

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-102256
Share on other sites

also try superpro

http://www.superpro.com.au

they make the polyurethane bushes whiteline sell, or so the suspension guy told me. they are blue, not yellow, and cheaper, thats all the difference, same parts and quality.

Ive just done the castor bushes in my s13. much nicer.

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-102374
Share on other sites

Benm,

Do you have coilovers? I have then and they will give you a rattling sound, that is because they don't necessarily use rubber between the spring and the top of the suspension, therefore when you go over a stiff bump the spring compresses and then rattles against the metal of the chassis.

If you dont have coilovers thenI don't have any suggestion.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/6318-bushes/#findComment-102614
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...