Jump to content
SAU Community

Recommended Posts

Hey guys, calling on the gurus out there who have done this before.

Ive got a Bosch intank pump that i want to put into an R32 GTST, but in order to maximise current and performance, i would like to run seperate wiring to the stock pump all the way to power and ECU.

I am told that you need a seperate relay setup and heavy gauge fused wiring. I was thinking of keeping the stock wiring as is and then running the aftermarket pump just incase the pump gets sold or changed back to stock.

Is there a FAQ or Tutorial about doing this? What are your experiences and how did you overcome spefic problems.

Im not an autoelec by trade, but i have done a few custom wiring installs before, just need a circuit diagram witha general direction to where i should be heading thats all :(

My impression is that i need to get the fuel pump on signal from the ECU, switch a relay that powers the fuel pump and presto your pump is on. Fuel pump signal goes off, pump turns off. Everything is grounded nice and tidy back to the battery for optimum performance.

Does the R32 have a current droping resistor prohibiting the amount of voltage that goes to the pump during light loads, like on other nissans?

Thanks guys

--

----

Costa

you pretty much got it on the ball, and if you do decide to put the std back in it doesn't hurt to have upgrade wiring there.

as for the dropping resistor, dunno if the R32 has them, but they are a pain in the arse anyway and you can do away with it, dunno how tho.

I haven't seen differential voltage on R32's. It doesn't matter anyway, since it is only switching voltage. Simply select a suitable relay for the posible range of voltages. I use a solid state relay, not mechanical as it is located close to fuel. No sparks for me.

I run both pumps off the same relay. So it is simply a matter of pulling up the standard wiring harness, plugging the switch wiring into the relay, and then using the harness (I made up) to connect to the pumps. To put it back to standard I just unplug the relay remove the external pump and plug the standard wiring back into the standard pump in the tank.

Hope that makes sense:cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...