Jump to content
SAU Community

Recommended Posts

Im dropping the price to $25000 or i will negotiate a better price with out a roadworthy.

1992 R32 GTR 96000kms Factory Grey colour, body in vgc as is the interior.

3 inch cat back exhaust with hi flow cat,

please note there will not be any test drives unless a deposit has been put down.

Im looking at $25k pm or email [email protected]

Link to comment
https://www.sau.com.au/forums/topic/64274-eoi-r32-gtr/
Share on other sites

Can you please tell us a bit more about the car to help interstate people a bit more?

Scratches or dents? Has the car been in any accidents? Resprayed?

Compression tested the engine? Leak down?

etc?

Link to comment
https://www.sau.com.au/forums/topic/64274-eoi-r32-gtr/#findComment-1227087
Share on other sites

Can you please tell us a bit more about the car to help interstate people a bit more?

Scratches or dents? Has the car been in any accidents? Resprayed?

Compression tested the engine? Leak down?

etc?

The body is in vgc, had the roof sprayed as it had some dents on it, the previous owner reckons he didnt have a garage and and some branches etc would have fallen on the car as he lived neat the bush.

No dent to think of a few littke scratches on the front bar.

Ive been meaning to compression test the engine at work just have to get around to it.

No leak down test performed as i have neved had the car at a mechanics.

Link to comment
https://www.sau.com.au/forums/topic/64274-eoi-r32-gtr/#findComment-1227118
Share on other sites

Thanks for that mate...

Would probably help interstate buyers a lot if you could do the compression test and swing by a panel beater and ask them if it's been in any accidents...

Would make the decision to fly over to Melbourne that much easier if those two factors were known :D

Link to comment
https://www.sau.com.au/forums/topic/64274-eoi-r32-gtr/#findComment-1227191
Share on other sites

Thanks for that mate...

Would probably help interstate buyers a lot if you could do the compression test and swing by a panel beater and ask them if it's been in any accidents...

Would make the decision to fly over to Melbourne that much easier if those two factors were known :D

thanks for the pointers merli,

il do a comp test next weekend as im the keenest to known how the engine is

When i had the roof done my panel beated did check it over and said the only think he seen was the front bar was replaced and it had a aftermarket fibreglass one on it.

my guess is as good as anyone elses to work out what happened to the bar.

Link to comment
https://www.sau.com.au/forums/topic/64274-eoi-r32-gtr/#findComment-1227795
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...