Jump to content
SAU Community

Recommended Posts

A way to test the clutch integrity is to put it in 4th gear, pull the handbrake on as hard as you can without breaking it and try to take off. You may have to accelerate a bit. The aim is to stop the car from stalling. If it tries to keep running or you can keep it going for a while (like 2 seconds) then the clutch is had it.

When the clutch is fully engaged, ie. your foot is not on it, the car should stall immediately no matter how hard you try.

If it stalls immediately, start looking at other things.

BTW. It would NOT be a good idea to rev it to 6000 rpm when performing this test as you'll end up like my idiot friend who drove his car through the end of his garage. Bloody GTS4 traction. 2000 rpm is enough.

Link to comment
https://www.sau.com.au/forums/topic/64837-r33-laging/#findComment-1213257
Share on other sites

My second guess would be to start looking at Turbo and AFM. Check for end play in the shaft of the turbo, in that model there should be none at all. Check to make sure it spins freely, however, don't spin fast. Just turn it half a turn gently. If it appears ok, next thing to check would be the wastegate actuator. With an air pump or mightyvac you need to simulate boost pressure to ensure the actuator is working at the correct level.

How is the fuel pump? Do a flow and pressure test on the pump to make sure it is flowing at the correct rate.

Are there any error codes?

Check to make sure the AFM is clean.

Check to make sure there are no vacuum leaks from anywhere. Get a water sprayer (like hairdressers use) and soak all hose connections while the car is running to check for leaks (you will hear the idle change when it sucks up the water).

Start with those things and if they don't help, post a reply.

Link to comment
https://www.sau.com.au/forums/topic/64837-r33-laging/#findComment-1214851
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...