Jump to content
SAU Community

Recommended Posts

Okay im gona go down the strip tonight for the first time. Normally when i launch my car i ride my clutch and slowly roll forward then release. Will this give me a faulse start?? Should i have the handbrake up then release it doing this method or should i jst drop the clutch even though i normally dnt do this way off launching my car.

Should i do a little burn out before i race to will this give me more traction? and should i jst drop the clutch.

Thirdly, what do i need to take helmet etc, and any other points i should consider???

Link to comment
https://www.sau.com.au/forums/topic/65507-goin-to-runs-need-advice/
Share on other sites

You need helmet, rego papers, long sleeve pants/top and $45.

If you roll out of the staging beams before the green light, then yes you'll false start, but you'll still get an ET, so it's not really a huge mistake to make. The start area is flat, so you don't need your handbrake if you've got your clutch engaged - just drop the clutch on the last yellow light and you should get a good reaction time. To what degree you feather the clutch really depends on the tyres you're running - obviously the better traction you get, the quicker you should let the clutch out. It'll take some practice...i've been a couple of times now and I still can't get it right (shitty tyres don't help though).

As for the burnout, it's not really going to make much difference traction wise if you're running street tyres...much of a muchness really.

Good luck :(

1. Enter via the competitors gate (old rear entrance for the EC Racetrack).

2. Pay at gate ($45)

3. Park in the pits somewhere and fill out the form you are given (take a pen)

4. Line up at the scrutineering garage with your rego paper, license, filled out form and your entry ticket, you will get a wrist band.

5. Drive your car around to the garage and wait inline to have your car checked over (open bonnet, open boot, check helmet).

6. Drive your car back around into 1 of the 5 lanes and wait (usually about 30-40mins per run up until about 9pm then its about every 20-25mins because people leave/breakdown.

7. When its your lanes go just follow the guy infront of you and the marshall will mark the sticker on your screen and point you to lane A or B.

8. Burnout: You don't need/want to sit and smoke your rear tyres for 3hrs every run because all you are doing is wearing them out. All I do is drop the clutch from 3000rpm, let it spin (as it rolls forward) for about 5m and then just throw it in neutral and roll up to the staging line.

9. Staging: I always like to stage first before the other car, it gives you 10-30sec to settle your nerves, get comfortable in your seat (with your helmet on for a change). On the side tarmac part of your lane you will see a white line across the track, just move forward until your front tyres are close to this line, then watch the top 2 staging lights on the tree.

10. Launch (for me): Clutch in, handbrake off, hold the revs at 3000-3500rpm. When the lights go I just take off like a normal set of lights (so basically part drop, part ride the clutch). If it starts spinning the rears just back off abit, if it bogs well just hold on for a second or 2 until your revs pickup.

11. 1/4 Mile: Nail your gears, treat the car like you hate it or just drive like normal with the throttle flat, each to their own. Don't stop until you are past the big timing towers.

12. Follow the return lane all the way back past the staging around to the garage and grab your timing slip.

13. Repeat until either 10pm or your car breaks :(

Actually... I bet wsid.com.au has this written up somewhere :)

If it's your first nite seriously... don't worry about a burnout (its not required anyway except to scrub off the water) and don't try and cut an 11sec pass. Just learn to stage correctly (without looking like a knob and staging with your rear tyres) and get across the finish line in 1 piece without leaking fluid or breaking your clutch. As you get over those bits your times will drop by themselves...

Give me a wave if you see me [MOVEIT]

Happy drag racing !!

just drop the clutch on the last yellow light and you should get a good reaction time.
I actually take-off when I see the 2nd yellow light come on, it gives me consistent 0.1-0.3sec Reaction Times (which is why I win the majority of my races unless i'm up against a Pac "race" Car).

Launching on the last (3rd) yellow light will give you a 0.8-1.0sec R/Time :(

:)

I actually take-off when I see the 2nd yellow light come on, it gives me consistent 0.1-0.3sec Reaction Times (which is why I win the majority of my races unless i'm up against a Pac "race" Car).

Launching on the last (3rd) yellow light will give you a 0.8-1.0sec R/Time :(

:)

lol, no wonder I can't get any better than a 0.2 R/T - I'll try that next time :)

I was keen to go tonight, but something's come up, so im aiming to be there again next week instead.

Good luck tonight fellas - look forward to reading about that 13 sec pass benm :)

Also, it doesn't matter how long after the green light comes on before you actually take off. Your ET is recorded from the time you cross the second staging beam until you cross the finish line. Plenty of cars sit for a while on the line getting set as they are after a time not the win. But if you really want to beat the car in the other lane, then take off on the last yellow (or second one if you have slow reflexes :() The main things is getting used to the proceedure, staging and gear changes. Have fun!

Have fun, my first time I loved it.. I also tried launching on different RPM's as each car's setup is different you might find that you could drop on each run on the last yellow but use different RPM lauches to find the right amount of traction to wheelspin that gets your turbo and ass moving :(

good luck.. :)

I have heard some people complain about of lack of traction using street tyres, but I personally haven't had any trouble. 1.8 60 ft on my first pass with an open diff (S3 RX7 Turbo) on street tyres. Alot of it is more than likely due to street tyres and 30+ psi. Use some semi's or drag radials and you will see the sub-1.8 60ft's :( But generally, it is stickier and also helps if they have a Test and Tune on that Wednesday for a big meet the following weekend.

silver gts-t - running street tyres, in my personal experience the track does not seem as sticky as the road! But I was told that it wasn't prepared properly for that particular meet.

Changing 2nd to 3rd my car actually fishy'd abit.... thats with Exhaust, Front Mount and Boost..... 13.9 first night ever at the drags with tyres at 36psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...