Jump to content
SAU Community

Recommended Posts

People could please make sure that if you do have these rims they are not the 6.5inch wide version. They are stamped 16/7.5 45 offset on one of the inside spokes.

These rims are possibly off the AWD non GTR Skylines not sure. But I have definately got two 7.5inch wide R33 Skyline Rims and I want 2 more.

Or will take 4

Link to comment
https://www.sau.com.au/forums/topic/66467-wanted-2-standard-r33-1675-inch-rims/
Share on other sites

my stockies are 6.5 wide all round.  i thought they were all like that.  might have to have a look again.  N/A's have 4 studs instead of 5 so they wouldnt be that.

Perhaps 7.5 inch wide are Series 2 rims.

i have two.

lemme know.

This should be in the Wanted To Buy section mate.

Yeah sorry about posting here, I thought this was the place for Victorian stuff.

Just sent an email to your hotmail.

Thanks

Pat

  • 4 weeks later...
  • 2 weeks later...
i have a full set of 300zx rims, willing to seperate for the right price. Let me know if you are interested. they are 16inch, 5 stud, not sure about the width and offset, but can check if you want.

Please check and get back to me.

If they are 16 7.5/45 offset they are right.

ha. you're in luck.

I tried measuring with a tape, but that got me all confused cos i didn't know where to measure from. Then i loked for writing on the inside of the wheels and found......16X7(1/2) JJ 45

looks like i've got what you are after.

ha. you're in luck.

I tried measuring with a tape, but that got me all confused cos i didn't know where to measure from. Then i loked for writing on the inside of the wheels and found......16X7(1/2) JJ 45

looks like i've got what you are after.

Very good.

Just pm me a contact number and we can take it from there

Thanks

They must be stamped 16/7.5 45 offset.
I think you are confusing R33/S15 wheels with the old 300ZX rims.

Also I just checked both (I have a set of both) and neither have any measurements stamped on them inside or out).

On my car the fronts are 16/6.5 and the rears are 16/7.5 and this is definetely stamped on the inside spokes.

I'm not sure what car the 7.5's came from but all I know is that they look identical to the front 6.5's..

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...