Jump to content
SAU Community

A31 Cefiro Body Dimensions

S13Deviat
 Share

Recommended Posts

S13Deviat Grand Master

S13Deviat

Posted
Posted

Hey guys & gals.........have finally tracked down a suiting ceffie and should hopefully be in my hands within a month. (As long as all things go well once it gets here) :wassup:

Now i am trying find out the true width and length of the A31 Cefiro 88'. I have found some sites with listings but they seem a little off. I am trying to measure up if the beast will fit in the garage. If anyone could confirm or inform of the correct dimensions it would be greatly appreciated.

The dimensions i have found are 1486cm-width & 4760cm-length

Firstly the width seems a little 'skinny' and length seems approx correct. I dont have much room to spare in the garage as it is a little one and am looking @ dimensions of approx 4900cm-length and 2500cm-width.

As you can tell not much room to spare so if anyone has a spare 5 min, a tape measure, it would be greatly appreciated. Or alternatively if anyone has official dimesions...that would be awesome to!!!!

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/66579-a31-cefiro-body-dimensions/
Share on other sites
dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

It will fit no worrys. Im not going to go out and get a tape measure, but it will fit.

Your just maybe going to have to be a bit careful getting in and out of the car, more so if you have a passenger.

S13Deviat Grand Master

S13Deviat

Posted
  • Author
Posted

AHAHAHA well hey a little persuasion gets you a long way!! :wassup: :rant: I think i may have to move some shelving in it but all should be good. Well all things going well, it will be another Ceffie hitting the North Shore :headspin:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Does the scanner do all the CUs in the car, or only the ECU?
    • albyz34gt
      R34 N/a And R34 Turbo (gtt) Transmission.. Uh, Problem.

      By albyz34gt · Posted

      @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • RB25inside
      R34 Handbrake light saying ON and intermittently flashing

      By RB25inside · Posted

      Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • GTSBoy
      ECU sees many times the speed than speedo does (R34 swap)

      By GTSBoy · Posted

      Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...