Jump to content
SAU Community

Recommended Posts

Hi, Can anyone confirm that ARP rod bolts (part no 202-6005) will be a direct fit for my RB26 conrods, that are going in my RB25DET? When I made the order, they were advertised as ARP RB26 bolts, but when I recieved them today, they are marked SR20 bolts. I have been told by one performance supplier that these are the wrong size, and others have told me they have used them in their RB25 & 26 without problem. Can anyone help? Thanks.

Link to comment
https://www.sau.com.au/forums/topic/67590-arp-rod-bolts-confirmation/
Share on other sites

I was told recently that ARP dont accully make rod bolts for the RB26 and you can use the SR20 bolts, but I was advised against it because they a touch too short(or somthing like that) and to use the tomei ones. Which I got from greenline for about $160-180. This is what I was told when I went to purchase the ARP ones anyway. Hope that helps

The ARP SR20 bolts are a tad shorter but the threads are plenty long enough to engage the entire nut. From memory, an ARP VG30 bolt also fits.

Hi Proengines, - How much risk involved using the SR20 bolts? I'm inclined to send them back to Modyourcar (they are supplied by Rocket Industries), as they said they would give me a refund, but still insisted telling me that SR20 and RB26 bolts are the same. Tomei bolts are only $65 more expensive - I'm not into taking any risks as my engineer is currently rebuilding the engine and I don't want to spend money fixing any mistakes. SR20 bolts&nuts = $210 shipped/Tomei $270 shipped?

Thanks everyone who posted - Just had to be sure

I just did some checking and I have to correct myself. a standard RB26 bolt has an underhead length of 60mm and the ARP SR20 bolts have an UHL of 58.5mm so there is a 1.5mm difference in the length of the bolts. If you fit the bolts to the rod, the ARP protruded 7.3mm from the spotface where the nut seats and the std Nissan bolt protrudes 8.5mm. The nissan nut is 7.8mm thick so the bolt protrudes 0.7mm through the nut. The ARP nut is 9mm thick so the bolt finishes 1.7mm down inside the nut. thats probably a lot of figures but from them I wouldn't use the SR20 bolts.

As I said, we have used the VG30 bolts with no problem, they are part # 202-6004 and work fine. They are a touch longer, I'll attach a photo so you can see.

Exactly and beat me to it as my guys are busy but was going to get them to do same re figures. The other prob is the face of the nut of the ARP SR20 is smaller than the factory nut so in a sense weaker. I would use factory rod bolts or Tomei VG30 might be OK.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...