Jump to content
SAU Community

Recommended Posts

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Slightly off the topic has anyone tried the WA made octane booster. Quiet a few mags reckon it's the ducks guts so to speak.

I can just see me at the local BP in Armadale trying to buy a 44 gallon drum of Toulene... maybe i should send my blackfella neighbour down.. he'll do anything for a good laugh..

Rev210,

I agree toluene is one of the best octance boosters, especially for the price, about $48 for 20L, enought to treat 100L of fuel. In a comparison that I saw the Nulon rated higher than the toluene though, +2.7RON as opposed to +2.5RON. Many of the expensive octane boosters did f#@k all, +0.7RON, so it is worth finding one that works. The Nulon treats 60L and cost around $25, so it's not bad bang for your buck, plus less hassel in getting it than the toluene.

If anyone is interested I am planning on getting some VP Motorsport fuel, I have a friend who bought 400L of the $7.50/L stuff, but because of the bulk buy he only paid $5.50 a litre, not cheap I will admit but it makes a big difference to the way you can tune your car, much more timing!

Adam 32,

Macka probably pissed in the Coke bottle, thats why it did f#@k all.

See'ya:burnout:

Originally posted by GTS-t VSPEC

Rev210,

I agree toluene is one of the best octance boosters, especially for the price, about $48 for 20L, enought to treat 100L of fuel. In a comparison that I saw the Nulon rated higher than the toluene though, +2.7RON as opposed to +2.5RON. Many of the expensive octane boosters did f#@k all, +0.7RON, so it is worth finding one that works. The Nulon treats 60L and cost around $25, so it's not bad bang for your buck, plus less hassel in getting it than the toluene.

Nulon's octane booster is quite ordinary. Look at the volume for price. This is where toluene is a little different to 'bottle' octane boosters, it is more of a 'fuel base'. Nulon and products like it are not added in quantities upto 20+% nor can they be without serious harmful effects to the engine and an actual drop in performance.

In the reviews I've seen comparing different octane boosters ,including nulon's, wynns race formula was a suprise performer. Nulon in the same review scored quite average. This was a horsepower based test.

Nulon incidentally will never raise the octane level above 100 RON with BP ultimate 98 (infact most cannot) with 1L in 60L (<2%). Reviews that contend that it does are suspect (read advertising money) as this requires the additive to contain not less than 396 RON. Don't even get me started on the MON. Ask most serious racers what they think of this stuff compared to 'REAL' 101 racing fuel. Granted the formula in a these additves reduces volitility but, not through adding an octane base.

Toluene adding is just like the racing fuel, only better (no EPA restrictions apply to producing your fuel).

Rev210,

In the review that I have seen it showed that Nulon was the top performer, just better than Toluene, that is not to say that the reviews you have are incorrect, but measuring based on horsepower is not very accurate.

Everyone will find an octane booster that they like and that gives them a performance edge, doesn't make them right but it is their decision. Volume for price, at ~$20 for 500ml it treats 60 litres, compared to 20L of Tuluene (~$48) treating 100L. Just becuase it's in a smaller bottle doesn't make it less effective.

I am considering using VP Motorsport fuel, but at $5.50/L it makes it kind of restrictive. I will try different octane boosters including toluene and come to my own decision, not sure if I'm just wasting my money or not but if it gives me an edge then I'll try it.

See'ya:burnout:

Rev210,

I've just re-read the Octance Booster Review article. It was performed on a knock engine($200,000), which is the only true way to calculate RON. It showed Nulon and Toluene up top. This does not mean that they will provide any horsepower benefits by themselves. The higher octane rating will allow for more advancement, therefore allowing for more power.

Some octance boosters improve the octance rating by stuff-all, but contain nitromethane, which will add horsepower.

See'ya :burnout:

Originally posted by GTS-t VSPEC

Rev210,

I've just re-read the Octance Booster Review article. It was performed on a knock engine($200,000), which is the only true way to calculate RON. It showed Nulon and Toluene up top. This does not mean that they will provide any horsepower benefits by themselves. The higher octane rating will allow for more advancement, therefore allowing for more power.

Some octance boosters improve the octance rating by stuff-all, but contain nitromethane, which will add horsepower.

See'ya :burnout:

Knock engines are not how RON is calculated at the places the stuff is made, more likely to be a HPLC or something. You might notice on a 'knock engine' diesel rates higher also, it requires great cylinder pressures to actually combust.

Like I said before RON ought to equate to the 'octane' composition and poential energy as it suggests not its volitility as the 'knock motor' measures, though this can relate to the reduced volitility additional octane produces.

I've used the nulon stuff, wynns and a few others. The difference is nothing to write home about, any gain is usually through modest timing advance. 500ml in 60L ? This would mean the RON of nulon is over 792 RON ! Who are we kidding?

Toluene you WILL notice.

500ml of SFA Vs a few litres of real power.:D

Rev210,

I work at Murdoch University teaching Engineering, we have an Engineering Chemistry faculty here so I spoke to them about it. The have performed work for a number of the big petroleum companies, i.e.Mobil and BP, and although you can measure the number of grams of octane in the fuel on a HPLC, this does not give you its RON. All the companies have there own knock engines on which they perform this test.

I think we need to distinguish between improving the RON and improving the horsepower. The higher the RON the less likely the car is to ping at high boost, and therefore allowing for more timing and potentially this can give you more power. Whereas other boosters and toluene can give you both improved RON and improved horsepower, from the nitromethane, just by adding it to your fuel.

I would agree that in general you will feel f#@k-all difference between having octane booster or not, but it will protect your engine from pinging. It is only through the advancement of your timing that you will get any improvement.

See'ya:burnout:

GTS-t VSpec - So you mean that toluene contains nitro-methane? And the differenc in power gains between them all with no adjustments is actually the amount of nitro not the RON??

Dr_Drift,

Yeah that's right, octane by itself does stuff-all in terms of horsepower, hence why most people get jacked off with it, only useful if you can't get PULP and you need to bring the octane up. Some of the boosters contain nitromethane which produces more energy when burnt, therfore a bit more horsepower.

If you use octane booster on PULP for daily driving then I think your wasting your money, but if racing then it will provide an extra level of protection.

See'ya:burnout:

Has anyone tested "NF Formula"??

I used to put that in every tank of my 180 cause we'd advanced the timing with a fueltronics chip in it.... Used to run like shit without it... I'm assuming it was sensing detonation and resorting back to the low octane map. (You did all know that all nissans run dual maps and kick down to the 'safety' map when detonation is detected??)

Ran a 13.5 at kwinana at 106mph before I moved to melbourne... It was on a 30+ degree evening and I had NF Formula Pro Strength and 6 lt of toluene to help..... I guess it did....

Not bad for stock turb and cooler hey??

Doc.

PS: NF Formula was the ONLY additive that made it run sweet... EVERYTHING ELSE was shit

Originally posted by GTS-t VSPEC

Rev210,

I work at Murdoch University teaching Engineering, we have an Engineering Chemistry faculty here so I spoke to them about it. The have performed work for a number of the big petroleum companies, i.e.Mobil and BP, and although you can measure the number of grams of octane in the fuel on a HPLC, this does not give you its RON. All the companies have there own knock engines on which they perform this test.

Interesting stuff!

All the same I wonder how the knock motor calculates RON/MON, it can't be just to do with pre-ignition can it? I mean that would make diesel super octane rated, when it isn't?

Rev210,

Apparently this is how they do it, don't know about the diesel, it tends to run at much higher compression's and the fuel is run like a controlled detonation. I'm not sure whether you can compare diesel and petrol, as although they are both petroleum derivatives that does not suggest that they have the same detonation characteristics. Therefore although diesel does not contain large amount of octane it is relatively immune from the affects of detonation.

I have this excerpt from a magazine, which I know you think are propaganda for advertiser's and quite often your right, but here it is.

As the name suggest, a knock engine is designed to test the detonation or anti-knock rating of fuels and fuel additives. It's a slow revving engine capable of running most fossil fuels through an adjustable compression ratio. As the comp ratio increases, it accurately measures the intensity of the knock and determines the fules octane rating

Hope that clears up any questions.

See'ya

:burnout:

Originally posted by GTS-t VSPEC

Rev210,

Apparently this is how they do it, don't know about the diesel, it tends to run at much higher compression's and the fuel is run like a controlled detonation. I'm not sure whether you can compare diesel and petrol, as although they are both petroleum derivatives that does not suggest that they have the same detonation characteristics. Therefore although diesel does not contain large amount of octane it is relatively immune from the affects of detonation.  

The same engines test diesel and other fuels too don't they? I'm puzzled still.

Remember the formula 1 example: 104 RON fuel was the restriction so they added 7% n-heptane ( a relatively inert fuel ). 104 RON (basically all toluene normally rated 122RON/114MON).

Now if you can find a race fuel or additive with only 104 RON that can handle running an engine at 75psi of boost (5 Bar) your doing better than all the formula 1 teams ever could. BTW they were only restricted to 104RON not forced to use toluene.

Maybe its the MON thats more important is that measured the same way?:P

rev210,

I must admit I'm on the limit or past the limit of my knowledge, so its guessing from here on out.

Don't know it they test diesel's the same way, I didn't think they had an octane rating? The problem of detonation with diesel is not as big an issue as the design of the engines are such that they can cope with it, from what I've read.

I know that VP Motorsport 103 fuel has an octane rating of 107, and therefore stupidly high boost could be run in theory. The Formula 1 guys are automotive gods, and us mere mortals will never understand how they do what they do.

Sorry that I've got no answers, you hardly hear anyone mention MON, but it could be more important.

See'ya

:burnout:

Originally posted by GTS-t VSPEC

rev210,

I must admit I'm on the limit or past the limit of my knowledge, so its guessing from here on out.  

I know that VP Motorsport 103 fuel has an octane rating of 107, and therefore stupidly high boost could be run in theory. The Formula 1 guys are automotive gods, and us mere mortals will never understand how they do what they do.

Sorry that I've got no answers, you hardly hear anyone mention MON, but it could be more important.

See'ya

:burnout:

VP 103 has its limits and they aren't that high. Race fuels like C16 allow high boost but once again not that high. RM/2 is a more respected figure in race fuel terminology (mean RON+MON).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...