Jump to content
SAU Community

Recommended Posts

Im thinking about buying an R32 GTS-T.. ive got a 00' model honda integra GSi which i will prolly get around 17~18 for. Plus i have a few grand saved up.

I plan on buying one already here, since the import rule is kinda wishy washy atm... and id rather have the car checked out properlly.

An r32 gts-t specific question... do they have ABS? if not? is it possible to get ABS installed? like aftermarket?

Are their any differences between the 1993 and 1989 models?

Any specific problems i should look for when im looking at them?

*ps* i tried a few searches but i didnt work to well :D

differences between 89 and 1993 are mainly just visual. If you can get a later model it will probably better worth your while in the long-run, as there are quite a few 1989 ones around now. Some don't want much to do with a 89 model just because.

Some of the later models had ABS as an option, but it was pretty rare.

have owned 2 R32's and think that they are an absolutely awesome car to own and drive.

[/size]

Weaknesses:

suspesion - this can be overcome by getting a model that has aftermarket shocks and springs, castor rods, control arms, and buschs.. They have been driving for 10+ years now so this aspect of the car has copped a bit of a beating.

Engine Condition - u plan on buying a sports car, so understand that it has been driven like one before you bought it... This means that for the past 10 years the car has been used for the same reasons you want to use it for (maybe worse). Have a full compression and leak down test done. A few hundred extra dollars on some comprehensive testing may save you thousands in the long run.. Take it to a reputable mechanic to be tested.

Fuel Pump - definately a weak spot on the R32. Try and get one that has had it replaced.

Door, window, and sunroof seals - prone to wear and tear, and could mean the car leaks when it rains.

Accident History - have the car checked from top to bottom - last thing you want is rust to appear down the track from cheap repair work.

Interior Condition - check the dash, gear boot, steering wheel, and the roof towards the rear windscreen.

------------------------------------------------

ABS

Speak to Just Jap www.justjap.com about having this installed

Don't totally rule out 1989's. We were looking for a 91-93, after 6 months of looking at loads of junk, one came along, which happened to be a December 1989. After having the engineer check it over we bought it because it is a great car.

The only other car that qualified to be checked out by our engineer was a 93... turned out to have loads of problems; troubled hydraulic lifters, had been in a prang but had a good quality respray, only had about 75% of the power it should've and many other small problems... some other idiot paid more than $15k for it - ha ha ha.

Happy searching... don't rush it.

exactly take your time.

but get 1 cause the kick a$$!!!!

really fun to drive, you will notice alot you will just look at and say "i dont think so!!"

but u can find that has been taken care of. it will last forever! good ol rb20

thanks for the tips guys, quite interesting.

With the ABS.. has anyone had ABS installed on their 32? is it dodgy/good?

Do you think i should aim to get one privately or one from like a dealer... i noticed two at UAS, a 93 with about 170km's and a 89 with about 100km's.. both in my price range.. i personally havnt seen the vehicles in the flesh yet, been a bit busy.

oh also... price ranges suck! look for r32's meeting your criteria and value them yourself.

personally, i wouldn't go for one with 170ks... the closer you get to 200, the more stuff breaks ... but hey that's just my opinion. comprehensive checks will tell you the quality... might reflect k's, might not depending on the previous owner.

when i was looking... i came to the conclusion that any car that i didn't have to jump on quickly (before all the other young guys looking for r32 gtst's snapped it up) wasn't worth it... the one on uas makes me wonder - looks nice though, go check it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
    • Sorry, just assumed that talk of coloured pads meant EBC red/green/yellow/shit stuff. I don't know the DBA pads, but it's a reasonable bet that they will be OK. DBA make good stuff generally. Those 4000 series rotors I linked to are very good. I may well replace the RDA rotors I have with those when required.
    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
×
×
  • Create New...