Jump to content
SAU Community

Recommended Posts

HKS GT2510 - 300 PS Output

COMPRESSOR:

-Wheel- 63 Trim - 47.7 Inducer / 60.1 Major

-Housing- 60 Inlet / 50 Outlet - 0.60 A/R

TURBINE: -Wheel- 62 Trim - 53.0 Major / 41.7 Exducer

-Housing- GT25 inlet / Internal GT25 oulet - 0.64 A/R

Its a hell of alot bigger than a standard RB20 turbo though, do you think it would produce 300hp? with mods such as stainless manifold, stainless dump, 3" zorst front mount bigger injectors, fuel reg, bigger fuel pump running more boost?

Seems like that is what mine is, as it doesn't matter how much boost you wind up, it seems to run out of puff at around 200rwkw. The response if awesome though, very little lag

Mine made 200rwkw at 1.0bar, and has made 205rwkw at 1.3 bar - but at 1.3bar there is a extra 40rwkw at 100kph, so it gives it a big mid-range hit of power

Trying to work out if anything poses a restriction on my car at the moment, 210rwkw would be nice, even 220. Maybe with cams and cam gears it may get there

HKS GT2510 - 300 PS Output

HKS seem to rate their tubos about 10% conservative.

So 330 PS = 245 kw - 50 kw for transmission losses = 195 rwkw.

Looks like HKS and I agree.

Its a hell of alot bigger than a standard RB20 turbo though, do you think it would produce 300hp? with mods such as stainless manifold, stainless dump, 3" zorst front mount bigger injectors, fuel reg, bigger fuel pump running more boost?

Pretty irrelevant in this instance, a it simply runs out of airflow. So no matter how much you improve the efficiency, it has no more flow to give. Reducing the restrictions would (as always) result in lower boost levels, but they have no effect on the maximium airflow.

:P

Seems like that is what mine is, as it doesn't matter how much boost you wind up, it seems to run out of puff at around 200rwkw. The response if awesome though, very little lag

Mine made 200rwkw at 1.0bar, and has made 205rwkw at 1.3 bar - but at 1.3bar there is a extra 40rwkw at 100kph, so it gives it a big mid-range hit of power

Trying to work out if anything poses a restriction on my car at the moment, 210rwkw would be nice, even 220. Maybe with cams and cam gears it may get there

Do you have a dyno-graph? I was looking at a 2530 eventually but i think i'd be happy with those numbers if a gain in response was there with a 2510.

yeah sure

this is before and after - before was stock injectors/chip

after PFC and injectors

I want to try some cam gears next to try and get more top end - at the moment its pointless revving it over 6500. I want to move the power up in the rev range

It would make a awesome drift turbo, lots of torque midrange

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...