Jump to content
SAU Community

Anyone used MAHLE forged pistons in their RB25DET?

R33RWKW

By R33RWKW,
in Engines & Forced Induction

 Share

Recommended Posts

Cubes Grand Master

Cubes

Posted
Posted

An interesting read...

http://www.importbuilders.com/pistoncomparo.html

I went with wiseco as they appear to be quite common and proven in the rb30's.

It also made a big difference that my engine builder swore by them. lol

They also happen to be one of the lightest pistons.

But that said.. Wiseco and Arias are both very good pistons.

CP's and some of these others are also apparently good, I've personally heard on set of CP's that were very noisy in a CA18DET.

R33RWKW Proficient

R33RWKW

Posted
  • Author
Posted

My engine builder uses these alot, on many different street & race prepped 4-&6cyl cars (including Skylines). I did a little research on these, didn't find anything to worry about.

2BNVS - My builder got these in Lilydale, Victoria. He paid $1100.00. I did a search in Google & and there is heaps of info on them & they should be available in NSW.

I was all for the Arias, cost wasn't really an issue, as they simular in price, but I was convinced by my engineer (had a first hand look at some of the engines he has built) & by a few people using these pistons & who had their engines built at the same place. Let's hope I made the right choice.

DoughBoy Veteran

DoughBoy

Posted
Posted
CP's and some of these others are also apparently good, I've personally heard on set of CP's that were very noisy in a CA18DET.

Mahle are pretty good pistons, as long as you get the clearances to the spec sheet provided everything will be fine.

CP's are very fine pistons, they require little clearances (much less than Arias or Venolia). Due to the low expansion/clearances required, if they were put in a motor and spec'd to "normal" forged pistons you'll have excessive gaps, and probably get a bit of piston slap.. as well as blow by and wear. I'd be pretty concerned/annoyed if I was the owner of that CA18.

Cubes Grand Master

Cubes

Posted
Posted
I'd be pretty concerned/annoyed if I was the owner of that CA18.

Interestering you say that.

The builder is apparently the 'best' RB builder in SA, When choosing a builder for mine I threw a few questions at him and honestly had my doubts. So I went to some one else. :(

C_DawG Rising Star

C_DawG

Posted
Posted
id stick with well known stuff for anything relating to a motor thats getting a forged bottom end.

no pint risking to save a few $$ and then be stumped later.

Arias all the way

Mahle is a lot better known around the world then Arias mate, thank Porsche for that. Infact Arias are probably cheaper.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Mahle is a lot better known around the world then Arias mate, thank Porsche for that.  Infact Arias are probably cheaper.

i was reffering to use in Skylines.

each piston would be different for the respective motor.

many RB's run arias

proengines Rising Star

proengines

Posted
Posted

6 out of 10 Formula 1 teams use Mahle pistons. Thats a fair indication of their quality. Mahle is one of the worlds biggest piston manufacturers and supply F1, IRL, Nascar, WRC, V8 supercars etc.. as well as Mercedes, BMW, Porsche, Ferrari, GM, Ford etc.. They also own Cosworth Technology and ACL piston products.

They are a little dearer than most other pistons but quality costs money. Look at their F1 pistons, 19 500RPM, 15 000G when they change direction at that RPM and they stay together, thats a fair indication that they have it right.

Attached is a pic of their box-n-box design.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      R34 N/a And R34 Turbo (gtt) Transmission.. Uh, Problem.

      By albyz34gt · Posted

      @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • RB25inside
      R34 Handbrake light saying ON and intermittently flashing

      By RB25inside · Posted

      Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • GTSBoy
      ECU sees many times the speed than speedo does (R34 swap)

      By GTSBoy · Posted

      Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Duncan
      R34 Handbrake light saying ON and intermittently flashing

      By Duncan · Posted

      Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • RB25inside
      R34 Handbrake light saying ON and intermittently flashing

      By RB25inside · Posted

      Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...