Jump to content
SAU Community

Recommended Posts

i am posting this on behalf of Terry(modr33s2)

The time has come again where we have to have a cruise in the daytime and here are the details for that event.

DATE:16th April

MEETING POINT: Carpark next to Cannon Hill Maccas (cause maccas has little parking :P )

TIME:3pm for a 3:30pm leave.

then heading to the gold coast through bwcp and espy then onto the spit for some shots

just reply if ur coming

cheers mitch

Link to comment
https://www.sau.com.au/forums/topic/69743-16th-april-day-cruise/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

i would luv to come but cant ;) already made plans that i cant change, i went crusing last nite 1st weekend since i had the car, went to springbrook and then to panarama then to broady carpark good drive:)

not all skylines but :D had some 180's SSS's and a RX7 and a MR2. But i will be in future cruises for sure

Just check the map location as maccas is at the set of lights before the one with the circle around it.

At least I think it is...?

Your right :D

The maccas is around the area where the 4170 is for the post code. The red dot means theres an intersection there, so turn right there and maccas is just on the corner.

I should be able to come, dunno yet. I gotta give Terry back his locknut key I left at my work.

Yeah Ill probably need that someday and ill def be there with camera.

Good to see a great response.

Some maps for the people who dont know where cannon hill is, its off the gateway motorway just south of the gateway bridge.

Thanx smicknissan20.:P

i think that there should be a meet spot for gold coasters also say 4:30 at yatala bp. Plus i also might add i dont think ppl will be keen to go along the espy maybe just straight to the spit. Anyone thats wants to go to the espy ect can also do so, plus i might add the ralph swimsuit model final is on in the cavil mall after 6 haha i so have to check that out :P

i think that there should be a meet spot for gold coasters also say 4:30 at yatala bp. Plus i also might add i dont think ppl will be keen to go along the espy maybe just straight to the spit. Anyone thats wants to go to the espy ect can also do so, plus i might add the ralph swimsuit model final is on in the cavil mall after 6 haha i so have to check that out :)

I will try to get to yatala bp by 4:30 and straight to the spit. Now that i know of Ralph contest (growls:aroused: ) will be keen as well. And just for clarification what is espy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...