Jump to content
SAU Community

Recommended Posts

Do R32GTST brake calipers, rotors and pads all fit straight up to a Cefiro?? or is modifications required to the brackets and brake lines? I recal reading that many ppl run this setup, although just want to confirm there isn't any stuffing around with adapter plates etc. I've already got the 5 stud hubs on the car......

I'm in a urgent need to know basis as i've been unable to source 5 stud rotors (or blanks) for the stock cefiro brake setup as seen HERE and am looking at resorting to upgrading the whole setup to R32 GTST brakes.

Cheers

Ben

Link to comment
https://www.sau.com.au/forums/topic/70882-r32gtst-brake-upgrade-for-a31-ceffy/
Share on other sites

they bolt straight up...but a31/s13 brakes use the banjo bollts for the brake lines, and skyline/z32 etc calipers use a compression fitting type line...you can still use the banjo bolts though, althoguh it's too long, so if you dont wanna cut the bolt, just use a few more copper washers...just need to do it up tight. it's a good time to upgrade to braided lines for skylines :spank: just like i've done

yup well it all went well. all bolted up fine. and yup just took the banjo bolts down to ABS to get it cut, easier then me stuffing them up. got a feeling i might need to upgrade the brake booster some day to give a more firmer feeling, how many of you who have done this conversion have upgrading thier booster aswel? or did u just leave it? But other then that was a pretty easy job.

Cheers

Ben

  • 3 weeks later...
they bolt straight up...but a31/s13 brakes use the banjo bollts for the brake lines, and skyline/z32 etc calipers use a compression fitting type line...you can still use the banjo bolts though, althoguh it's too long, so if you dont wanna cut the bolt, just use a few more copper washers...just need to do it up tight. it's a good time to upgrade to braided lines for skylines :D just like i've done

Where did you get the braided lines from? Off the shelf or custom made? How much did they cost?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...