Jump to content
SAU Community

Recommended Posts

As above. Its hard to explain what its really doing, i can really on tell my story and what ive tryed and soforth, so see how it goes..

ITs started with comming home after a long day at work..... Spent half a hour got changed and went out. Now i drove the skyline home. and it was running sweet as. Now after hoping back in. No go. it seemed it didnt want to even bite on cranking. It was getting spark and getting fuel. (by the looks of it). After 30mins of waiting. she seem'd to of went. GREAT!

40 mintues later of driving. She started to break down. Missing. Coughing. It started with a bit of a miss/stumble on boost. (6psi atm) backing off the throttle and back on cured it. Then it became progressivly worse. Light throttle Intoduced large amounts of missing. And over the cause of 3km it wouldnt of even idle.

TRying to get up a hill was entertaining.

SO i was sitting on the side of the road in pitch back looking around my engine bay with my little pen with a light on the back of it. And noticed my water temp sensor plug had one of the terminals off, inside the plug hosing. Here's me thinking "Yippie" She will go now. Which i was right. Sort of. Still missed only running on 5 cylinders. This got me able to drop this off at a Friends aunty's place so i can come back for it. and so she was safe.

Next day........... **ding**

Had a look. By the looks on every plug. Overfuling. they were all foued and coated in fuel. Cleening them made no improvement in running. as well not it wont even idle.

Ive replaced. "Water temp sensor", AFM, FPR, dizzy cap. Check fuel pump. and line blockages. Spark is strong and timing is fine. The top of number 5 injector is now leaking, yet again i had only just replaced it.

Its now the point of. no matter what i do the plugs foul. Cleen them, bang foul.

Any idea's ?

Its now at the point of. I replaced the FPR 2 nights ago. And the fuel lines seemed to of primed alot better than the other Fpr did. But now my Fuel pump is pulsating. Its getting a perminant 12v sorce from the battery and is Switched throuh a Relay thats trigured off the car alarm.

Link to comment
https://www.sau.com.au/forums/topic/72154-l20et-overfuling-badly/
Share on other sites

Sound like what my FJ was doing when I( first got it. Turns out (after much swearing and setting up a compressor to push 10psi into the cooler pipes) that a hose (might have been positive pressure, I guess it couldnt have been vacuum because the engine wasnt running when I found it) under the inlet manifold had come off. It was just in the right spot that you couldnt see it from underneath or above the car and you couldnt really hear where the noise was coming from, but once I put it back on it was fine

It would definitely have been overfuelling with the broken water temp wire - the ECU would think the engine was cold and it delivers much more fuel to a cold engine.

I suspect the excess fuel has destroyed the plugs. I think new plugs should solve all your problems (but I've been known to be wrong before!).

Well, you guys were thinking along the same lines as me, And i replaced all my leads and plugs, with standard bp5es. Its been running better than before i can now rev to 7k, "not much tho" when i used to run out of spark at 5k. This is only on 6psi 3rd gear has a hell of alot of pull.

Heres a good one, Why does 1st and 2nd have no pull, evenknowing its at 6psi, but 3rd gear just honks compared to 1st and 2nd

not that im aware of....my NA C210 was doing exactly that, (l24e) and it turned out to be the afm connection....maybe you have a dodge wire in the loom? check that out...there may be no prob with the hardware at all.

ah, if your relating to my Ovefuling problem, luckly thats sorted. I noted when it was doing it, AFM. and repalced that. which was still doing the same thing. But lucky it took me a while but found out all the leads had broken down. wouclnt show any problems without a load on them

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...