Jump to content
SAU Community

This is a Rediculous!

noony

By noony,
in Australian Capital Territory

 Share

Recommended Posts

noony Explorer

noony

Posted
Posted

Hey all,

Long time since I have been on, buts its been a long time since I have really had the car back.

Long story short, I was in an accident in Late November, I got the car back after 3 months....

Ive had the car back for *about* 3months.

So today on my way home from work my entire Water Pump Housing cracked off and sent the fan partially through my brand new radiator!

Oh so annoying. Anyway, tomorrow I will find out if the Smash Repairers will fit the bill cause they obviously didnt replace the water pump even though it had been hit/damaged from my front on accident.

Im guessing there was a hairline fracture or something.

Here are the pics...

Link to comment
https://www.sau.com.au/forums/topic/73837-this-is-a-rediculous/
Share on other sites
noony Explorer

noony

Posted
  • Author
Posted
Fracture + a very very tight belt?

Yea, I was thinking that perhaps the belt was tentioned far to much and stressing the pump to much...

But you would have to be Hercules to do it that tight and not realise?

Im thinking that what may have happened is that the shaft was slightly damaged in the accident and it has grabbed on my way home. Im sure that even at 4k RPM it would be easier to snap that than to free itself up....

Hmmm, all speculation... I just really need it fixed.

Bullet32 Veteran

Bullet32

Posted
Posted

Yeah it did happen to me, exept it happened with a brand new one the 1st day that it was on!

I got my money back for the pump plus a replacement pump and the money for a new fan and radiator, all from super cheap auto (took 2 months to get it though).

I put the pump on and I know I didnt over tighten it so I dunno what happened.

FoX Collaborator

FoX

Posted
Posted
Yeah it did happen to me, exept it happened with a brand new one the 1st day that it was on!

I got my money back for the pump plus a replacement pump and the money for a new fan and radiator, all from super cheap auto (took 2 months to get it though).

I put the pump on and I know I didnt over tighten it so I dunno what happened.

Dumb ass... it wasnt 1st day you had it on. If it were first day it would have broken when we were testing it. It was at least a few months after because we had just done my water pump and timing belt on my r33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      thumbsup
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...