Jump to content
SAU Community

Recommended Posts

okay, first stage mods are in and i'm very happy with the way the car is driving. its responsive and it has top end.

list of mods are:

-trust dd cat back exhaust

-hks dump and front pipe

-apexi super intake

-hks front mount intercooler

-powerfc

dyno chart is as attached. a gain of around 20rwkw was had after installing the front and dump pipe and powerfc. the blue line is before the powerfc tune. this is running stock boost...

that brings me up to about 160rwkw.

IS THIS LOW? i was expecting close to 180-190rwkw with this set of mods? what power have you guys got and what mods?

cheers,

Link to comment
https://www.sau.com.au/forums/topic/7389-r34-power-figures-is-this-right/
Share on other sites

how much is stock boost on an r34 with out boost you cant expect much power you a/f could be a bit leaner to get a better power figure but where they have been set is good all round.

the standard turbo only just supports 180-190 rwkw @ around 1 bar If you want power fit a bigger turbo and use more boost.

but when you do that your engine does wear faster cause it is making more power than it was designed for

meggala

stock boost is about 0.7bar. i want to run 1.1bar but the nylon wheel on the exhaust wheel will just disintegrate on 0.85bar (the HPI GTT did anyways).

looking for a 2nd hand GT2540 or GT2530...GTR fuel pump and injectors....will R34 GTR injectors slot into an RB25DET NEO?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...