Jump to content
SAU Community

Recommended Posts

that one pictured is a 90 series (twin turbo, non vvti 1J)...

hmm. i don't know much about it.

Anyways.....the same question but for the above car....how much are they going for in the market...the 90series?

Seing no-one has helped so far i'll be happy to lend a hand.

The car pictured is a JZX90 Mark II built from 1993-1996.

You CAN import and comply these however there are only 2 compliance plate holders for JZX series cars in Australia that i am aware of. A place in Brisbane and Auto wholesale in W.A.

Compliance right now is a total joke on these cars but they are seriously awesome, best 4 door sedan in their price range and even better than most twice, 3 times+ their price.

Good luck with it all, PM me or dojobi if you need any more help, we seem to be the resident JZX experts :stupid:

JZX 90's are avialable as I just got mine complied by Jim at JB WA and it is a magic car,

Contact him on Phone 0411 693256 as per DOTR's contact details or email him on [email protected]  

Link to find who has what is http://raws.dotars.gov.au/rawswebpublic/rawpubmain.asp

Hey man do you know if he has 100 plates as well?

How much is he charging for compliance on 90's/100's?

Cheers, hopefully will be getting my 100 at the end of the year, need to save a bit more to get myself a manual 100 :flamed:

100 Plates are avialable off Frank from CAM and his contact number is on the link but when serious email me your personal address and I will pass it on as I see then once a week.

Have a look at the yard's any way as I am just trading my 90 in when I get a 100 due to the pricing is so good.

They have a manual 90, 60,000 klm, 18's, lowered, manual and TRD stickers by current trends and they only want $19,990 to get the cars on the road, it was also the test car is is straight as.

http://www.autowholesale.com.au/ has all the info.

Ali there's no one compliancing 90 series atm. We've got a client who's desperately trying to find a compliancer as well.

Either way, check the RAWS website to see when compliance is available and from who.

Whilst the 100's are nicer.. I reckon the 90's in many ways have much of the same qualities about them, and that much cheaper. They don't look that much different on the inside, and pretty much slightly older revision of the same engine...with a few power upgrades I couldn't imagine them being too different to drive.

I'd say they'd be a bit more different than you'd expect. They lost a turbo and added VVTi, so instead of max torque at 4800rpm in the JZX90, you get it at 2400rpm in the JZX100. I can see what you're saying though. The 90s are a very good cheap alternative.

JZX90's are an awesome car, but JZX100's are a step up again and they have come down A LOT in price so are worth it.

Interior in the 100 is much newer and has genuine carbon fibre trim standard :aroused: plus it looks much nicer.

As dojobi said, 1 less turbo, VVTi (exhaust), better suspension set-up and looks a shite load hotter!

Cant wait for mine! DRIFTT which company did you buy your car through in japan? Just need to start looking into finding an auction website that is decent who i can buy the car through in japan.

Will be good to see another 100 on the Perth roads so let us know when you get it, less than 10 JZX100's road registered in W.A. right now, which is good, keeps them rare :headspin:

Cant wait for mine! DRIFTT which company did you buy your car through in japan? Just need to start looking into finding an auction website that is decent who i can buy the car through in japan.

Will be good to see another 100 on the Perth roads so let us know when you get it, less than 10 JZX100's road registered in W.A. right now, which is good, keeps them rare  :headspin:

I got my Mark II JZX90 through Mark Hocking from www.mytrading.org and Jim complyied it, I will give it till the end of the year then get a 100, I want to tinker with the 1JZ-GTE first and see what hp I can get on a budget.

I do love my 90 so it will have to be a Manual 100 to make me sell.

just b4 raws came in i paid $5000 to have my jzx90 complied under SEVS and that wasn't with tyres.

DRIFTT i got 226rwkw on 12psi out of my manual 90 with a few mods.

Power wise the mods are:

Power FC

Cat back exhaust

High flowed steel wheel turbos

Airpods

HKS side mount i/c

Blitz dual sbc

I am so pissed atm.... payed mid to high 20s for the car as it was and have poured probably easy 15k into it and i haven't had one enquiry about it yet. :( atm seems i'll be lucky to get even low 30s for it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...