Jump to content
SAU Community

Recommended Posts

I would like to run methanol as a fuel as I have seen many cars benefit from the changement. Rayhall turbocharging claims on their website that you can add approx another 15 degrees of timing into your engine which is heeps which changement from pump to methanol! In addition, I have also read that methanol can give you an extra 20 percent power over pump fuel (providing your engine can take it).

Who has experiences with methanol?

Who has seen benefits?

What are the disadvantages apart from needing to changes injectors + pump (due to requirement of twice the normal flow since methanol needs to run twice as rich as petrol alone) and legality?

How much is it and where is it available on the gold coast?

What is its octane rating?

Does anyother fuel compare to methanol for power/dollar?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/74179-methanol-as-a-performance-fuel/
Share on other sites

Methanol is a fuel only ever used in darg cars and the like, it's not legal for road use. If you have ever stood near a car running Methanol you would know why. Apart from that you have to run a completly new fuel setup for it, i don't know specifics but i know of friends in the drag scene that have mentioned it.

If you want to run a better fuel than 98 you would still have to stick with a fuel like VP racing, that's about 103 and it's still unleaded so you can use it on the street. It's about $3.50 per litre though.

Methanol is used in drag set-ups as it will makes ya eyes water from the fumes. The fact is that most methanol set-ups on road cars are not 100% methanol (read this is for the strip only not for street use).

Basically Methanol lowers the intake temps and increases ron levels so more boost can be run without the problems of detonation. The system has to be set up correctly and not just "added to the tank". Its not an octane booster so don't even think of it like that. Most people run an additional injector or two from a fuel cell, separate lines and pump. I have seen a couple set up on N/A and turbo cars and have run effectively assisting in bring down 1/4 times and boosting top end power.

At the end of the day unless you have experience in fitting a system the cost will exceed the benefit. Stick to VP race fuels as listed above if you need increased octane. To reduce inlet temops the CO2 systems work extremely well, I prefer to use only externally on intercoolers as this has worked the best from what I have seen from properly tuned cars!!

I would like to run methanol as a fuel as I have seen many cars benefit from the changement. Rayhall turbocharging claims on their website that you can add approx another 15 degrees of timing into your engine which is heeps which changement from pump to methanol! In addition, I have also read that methanol can give you an extra 20 percent power over pump fuel (providing your engine can take it).  

Who has experiences with methanol?  

Who has seen benefits?  

What are the disadvantages apart from needing to changes injectors + pump (due to requirement of twice the normal flow since methanol needs to run twice as rich as petrol alone) and legality?

How much is it and where is it available on the gold coast?

What is its octane rating?

Does anyother fuel compare to methanol for power/dollar?

Cheers

Methanol does allow you to run more ignition or boost. we ran 35psi on methanol.

Intake air temperatures are very low. Dont have to run intercooler. Fuel is good for racing only. Too fidly for the street, plus it is allegal. Fuel is very corrosive. It attacks everything. have to run serious filter system. Most people will argue that running electric pumps is trouble. i tend to agree, we had trouble with pumps. Mechanical fuel pump is way too go. Make sure your tune is good as methanol is not as forgiving, serious melt downs occur. But if your setup & tune is good, you will see the benefits. Its just a bit of trial & error.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...