Jump to content
SAU Community

Recommended Posts

Hi Guys,

I have two brand new and unused NGK oxygen sensors. They are the direct fitment EL Falcon variety -- part no. 0ZA23-D2 / stock no. 0192 -- which, as per this thread, work with R32 (not GT-R) and R33/R34s (inc. GT-R) and are a great way to drastically improve your fuel economy: some people have double their milage per tank. You need to swap over the connector, but its dead easy (see the thread linked for details).

As mentioned, both are new and unused: I purchased them exactly two weeks ago in the belief that they fitted R32 GT-R dumps. Doh!. One is still sealed in box, the other (pictured below) was opened only to find it was the wrong size: it hasn't been used and the grease under the plastic cap is still there.

They cost me $75 ea. After $65 per sensor. Pickup in Sydney is fine and happy to post.

falcon-o2-sensor.jpg

Cheers,

Lucien.

good price, should sell quick...GL

by the way guys, Everyone should replace their O2s, out of reasons, like they seem to stop functioning correctly after your car Clicks over 100000KM. Due to having the old O2, your car drinks more juice too. Apart from that the cops dnt like old O2 sensors as they are "pollution" for AUS, so they decide to give ya a Nice fine, when they smell the Petrol around your car.

I get at least 50Kilometers per Tank more, after i replaced mine.

Got rid of them Pertol Fumes, and by the way i PAYED $180 For the Sensor.

CHeerS.

ratedGTR: Thanks matey.

The original Nissan's are stupidly expensive and there is no benefit (well, except for not having to spend two minutes modifying the plug): these aftermarket ones represent great value given you can make the cost back in a couple of tank fulls of petrol :P

IIRC, O2 sensors are only officially rated to last 40,000KM: most people don't bother replacing them then wonder why they have crappy fuel economy.

Lucien.

Hi Lucien ;) OCAU :rofl:

Anyways ill take it the one in the box $65.

Need to read up on how to make it fit in my R33...

Dont suppose I can meet you somewhere like your house so u can err help me install it? hehe

d00dz: Hey matey. Done: PM me about how you want to pay/post/pickup whatever :rofl:

Edit: Just so others know, I still have the box for the opened one.. its just been opened (der) ;)

Cheers,

Lucien.

hey Lucien did you manage to find an after market one to fit the R32 GTR?

Hey,

Check the last post in the thread I linked in the first post of this thread. Not sure if the Trust dumps have the same fitment as the R32 GT-R, or the other R-series though..?

Lucien.

Guys,

This is not an auction: please don't PM me asking me to accept less and/or pay for postage. As I have already explained, I am loosing money as it is and asking me to drop the price further and/or cover postage is insulting. If you can find them cheaper (and I doubt it: Repco wants about $82-85) buy them there.

Lucien.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...