Jump to content
SAU Community

Recommended Posts

Hey... I've got a stupid question..

I need to replace my battery.. it's constantly losing charge after a week of not being used... only problem is that on the GTR the rear strut brace is in the way and you can't get the battery out.

So my question is.. can I remove it and replace it myself?

Is it hard to do?

My only concern is that its a structural support and by my thinking may cause the strut towers to shift a little if removed and make it impossible to put back on.

Link to comment
https://www.sau.com.au/forums/topic/75742-r33-gtr-battery-changestrut-brace/
Share on other sites

Depending on the size of your battery you could slip it out above the strut brace.. i can get mine out/in like that (gotta tip it sideways)... if you have a bigger battery you'll have to take the strut brace off. Did it once, can't remembe rit being to hard - you'll be fine. Its to help stop the body flexing not to hold it in place. :(

Hey... I've got a stupid question..

I need to replace my battery.. it's constantly losing charge after a week of not being used... only problem is that on the GTR the rear strut brace is in the way and you can't get the battery out.

So my question is.. can I remove it and replace it myself?

Is it hard to do?

My only concern is that its a structural support and by my thinking may cause the strut towers to shift a little if removed and make it impossible to put back on.

I did mine mate and didnt have a problem.

Clarkey

Jesus Al, you been hiding? Best you be at the Sandown track day or the next club meeting for a catch up before I pi55 of to Qld. Probably leaving late July this stage.

I had a look today and the brace will come off easy as. Gotta be easier than trying to work around it. Even the GTSt is a biatch to work on back there.

Hey... I've got a stupid question..

I need to replace my battery.. it's constantly losing charge after a week of not being used... only problem is that on the GTR the rear strut brace is in the way and you can't get the battery out.

So my question is.. can I remove it and replace it myself?

Is it hard to do?

My only concern is that its a structural support and by my thinking may cause the strut towers to shift a little if removed and make it impossible to put back on.

Just undo the passengers side and loosen the drivers side mate .

When you change the battery just do it up again dont adjust the centre nut at all and it will be the same as before .

Stolly,

I fitted a heavy duty battery to my R33 GTR a month or so ago, and despite looking a little tricky its an easy job.

Simply remove the single bolt on each side holding the rear brace in, then remove the battery clamp and prepare for a good half hour of leaning over and loosening off the battery terminals, as the others have said you need to use some care here, but essentially its a simply swap - out with the old, in with the new.

:rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...