Jump to content
SAU Community

Recommended Posts

Hi everyone

I got my new car yesterday and i noticed a couple of times when idling it will just start adling up and down without anything being touched after a while and sometimes it will sit at around 800rpm steadily and then sometimes around 5/600. Is something wrong? or do they just have dodgy idle sensors or something cause my last 1996 series 2 gts-t didnt do it but this is a 1995 gts-t

Link to comment
https://www.sau.com.au/forums/topic/75777-upand-down-idling-s/
Share on other sites

Usually, a problem in the TPS is a constant high (around 1500 - 2000 rpm) idle. Usually caused by the sensor getting out of alignment and not sending the "throttle closed" signal to the ECU.

Variable idle is usually caused by a dirty / sticking AAC valve. That's the little cylinder on the back of the plenum chamber. It can be removed, disassembled and cleaned out with a bit of Car-B-Clean, then re-assembled and re-fitted without too much drama.

could be a vacume leak,

blind elk, thats true however my tps was out of wack in the other direction, what would happen, is it would idle fine, but you woul pull up to a stop sign, dip the clutch and the idle would **** around for a few seconds, worth checking, also the

and low speed driving was a bitch, car runs like crap, i dont think it will see 100% throttle either when you nail it

if your going to adjust idle , disconnect the brown plug on the solinoid behind it when your finished, reconnect it

Just had my 33 serviced not even a month ago, and after 3 mnths of pretty crappy idling, apparently a vacuum leak near idle starter motor was fixed, afm cleaned, tps adjusted, and timing reset.

Just last week it started ranging again from like 200-1200 rpm up and down as if i was stepping on and off the accelerator...

I have a non-oil blitz pod filter, and a blitz 3inch exhaust.

Any ideas on what else could be causing it in my particular case would be appreciated.

Cheers

-Serge

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
    • I've got MCA Blues on my V36 Skyline, and while I've managed to sort out issues with scrubbing/bottoming out by raising it a smidge and increasing the damping hardness, the rear end still sounds *super* noisy when driving on anything other than the flattest surface imaginable. It sounds like a small party of flamingos are just chatting away in the back, which makes me think there are several link points in the suspension contributing to the noise. Am I hearing dried out/worn bushings? None of it sounds like metal-on-metal, it sounds more like hard rubber squeaking on metal. It's been suggested that a bit of silicon spray on each bushing might quiet them down, but I'm not sure what material the current bushings are made of (probably factory, I imagine) and whether silicon spray will degrade that material.
    • The obvious answer here is get a ND2/3 RF with the Targa top. The red is nicer, too!
×
×
  • Create New...