Jump to content
SAU Community

Recommended Posts

Ok guys I think i am in the right area.

My 89 Ceffy has been great, BUT recently only in the mornings when taking off it feels as though someone is pulling the handbrake on at about 2000 to 3000rpm but as I drive through it it goes away, and then starts over again in the next gear so on and so forth till the engine warms up about 15mins or so later.

pls help with this issue as it is giving me the shits as well as the G/F

Ta

another Ceffy lover

ADRNLN

Link to comment
https://www.sau.com.au/forums/topic/76140-help-surging-engine/
Share on other sites

Mine does the same... its as if it retards the timing then all of a sudden goes back to normal and gives you a nice swift kick in the pants! Again, only happens when the motor is cold. Doesnt retarding the timing increase cylinder temps therefore warming the motor up quicker... might make sense?

JK

Yea mine does the same thing for about 5-10 mins (depending on weather), i think its just the engine retarding the timing to create more heat and warm the engine up faster, you would probalby find that if your cefiro is turbo the turbo starts spooling up earlier and with alot less throttle.

Does anyone know what sensor triggers this, is it oil pressure/temp or water temp or both?

i know this could be way off and slightly off topic, but would the fact that most of us are probally running the original auto computers (assuming with the limited amount of genuine manual ceffy's that were made) with now manual change anything with the timing when starting/warming up? (eg are the ignition maps different?)

anyway dude as i have mentioned and as jaik also touched on, check ur thermostat (could be siezed open) and coolant temp sensor (could be old and faulty/corroded).

other then that might be best to post ur issue up in the tech area as alot of r32 drivers would prob have experience/knowledge with such an issue aswel.

i know this could be way off and slightly off topic, but would the fact that most of us are probally running the original auto computers (assuming with the limited amount of genuine manual ceffy's that were made) with now manual change anything with the timing when starting/warming up? (eg are the ignition maps different?)

anyway dude as i have mentioned and as jaik also touched on, check ur thermostat (could be siezed open) and coolant temp sensor (could be old and faulty/corroded).

other then that might be best to post ur issue up in the tech area as alot of r32 drivers would prob have experience/knowledge with such an issue aswel.

mine is a stock manual and it surges when cold for the first 5 to 10 minutes or until the temp needle reaches the middled of the temp guage ..then it stops ...so i dont think its that

I have had a 32gtst, tt300 and the cefiro and they all have done it, if you find out what it is then your up for a noble prise in my opinion. I think its the timing being retarded, or a faulty sensor as latley I havent had it everytime I have started the car when its cold. I did go for a thrash and that seems to help it for a little while. The other thing my car gets is a slight splutter at cold idle as well, so the retarding seems to be right.

hope someone fixes this dilema

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...