Jump to content
SAU Community

Recommended Posts

If you want some cheapos Chris....I run Simex sm8000 i think they are. They hold up pretty well for me in the wet and dry. I was giving em a mild test before in the wet, and they were gripping well.....easy to control the throttle to bring on the wheelspin if thats your thing :D

They are about $120 each when i got mine in January...

Toyos are a good brand though.....

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1408420
Share on other sites

mmm, they seem cheap enough

Darren, where yours 16's? What are the sidewalls like? They will be going on the front first up, and I don't want a squirmy tyre on the front, it feels like shit if its like that

Thinking of going 205/55, but as the rims are 7.5" wide, it will stretch them out a bit and give it a bit more feedback through the wheel. I have run 205 on the front before, and to be honest, it felt better than the 225's as they had less sidewall flex, and braking was just as good. They are much cheaper too!

225's are a minimum on the back, even then grip is marginal

RaseR - what are the sidewalls like on the 17's?

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1409397
Share on other sites

i had transpath something or other on my old car, they gripped well since the car was close to stock, so ok for the price.. a bit slippery in the wet though!

and i think they are quite soft, as mine wore out to the thread in 15000kms :P :innocent:

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1409464
Share on other sites

I had a set of those on my car for about 3 years and never had any problems with them. Good grip on dry roads, decent grip on wet roads. Had a few hairy moments with 'moderate' take offs at traffic lights in the wet and also with a car load of people though! But definetely good for that price.

"The internet? Is that thing still around?"

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1409471
Share on other sites

getting two on saturday, will post results

Its was either a Toyo at $165, a Falken 326 at $160, or BF Goodrich at $220

I think for the $100 saving over the BF's, they are worth a shot. If they have soft sidewalls, I'll just run them on the back!

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1409824
Share on other sites

Hey Chris,The sidewalls on the Toyo TSW have more curvature then my previous Kumhos which were squarer (note, I have 8" wide rims on 235s and run 32psi). They still seem to be relatively stiff though, with no more noticable flex then previously - I'm only running them on the rear though.

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1409850
Share on other sites

mmm, they seem cheap enough

Darren, where yours 16's? What are the sidewalls like? They will be going on the front first up, and I don't want a squirmy tyre on the front, it feels like shit if its like that

Thinking of going 205/55, but as the rims are 7.5" wide, it will stretch them out a bit and give it a bit more feedback through the wheel. I have run 205 on the front before, and to be honest, it felt better than the 225's as they had less sidewall flex, and braking was just as good. They are much cheaper too!

225's are a minimum on the back, even then grip is marginal

RaseR - what are the sidewalls like on the 17's?

Yeah, my size is 225/50/16 all round. My front rims are 7.5" wide also. Dont really know if you can call em squirmy or not...they do me just fine in the dry or wet. I run them front and back. My last tyres were 205's on the front, and they feel the same as these 225's on now.

Agree 225's are minimal for the back.

I guess how much you spend depends on how hard you want to push your car then, eh Chris? :)

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1410475
Share on other sites

Well, first impressions are very good

Only done about 300kms on them, all wet, and they are very good. Will post up results as they get a few kms on them.

Extremely quiet at highway speeds

Pretty happy, decent sidewall too, so they handle well up front

Chris

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1418389
Share on other sites

Yeah, got the Toyo's

Went just for a front set, I hate buying a full set of tyres I have never tried before!

I want some dry weather dammit!! They seem really good so far, dry tests will be the key once they have a few kms on them

They seem to be a reasonably hard compound too, so should get a few kms out of them. Once they are scrubbed in a bit I will throw them on the back and see if they are worth getting for the rear. If they are I might get a set of Toyo Trampio's for the front, they look to be a really good tyre for the front

Will post up results!

Hows the 3L in the wet? Would be a bit of fun wouldn't it! I remember going for a lap around the block in the dry and it was pretty taily with the mech. diff in it. Mine is and it has half the torque lol!!

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1418852
Share on other sites

Very interesting in the wet...your able to keep the revs down and still get some tractions...just putt away and let the torque pull :P Mechanical diff hepls traction though..much safer i think than my old viscous diff...

IF you like wet weather well....its damn fun and scary at times :rofl:

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1419413
Share on other sites

  • 4 weeks later...

Well, about a month on these now, quite impressed!

Easily the best value tyre I have had on my car, getting a set on the rear in a few weeks.

Feel much better than the FM901's they replaced, very quiet too!

Link to comment
https://www.sau.com.au/forums/topic/76882-toyo-tranpath-sw/#findComment-1463381
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I should. But it already uses too much fuel for a daily. You might note my recco for engine chnages are almost exclusively to people who have it as a weekender/summer car. I don't even have room to keep the spares for this one, let alone another car.
    • If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
    • EDIT: PSA to whoever stumbles upon this thread. It is in fact a crack in the block that caused this concern. Just letting you know. In my case, a few cm long hairline crack going horizontally above the turbo oil feed. Classic RB shit I guess
×
×
  • Create New...