Jump to content
SAU Community

R34 Traction Control (Slip Sensor)

satanic
 Share

Recommended Posts

satanic Grand Master

satanic

Posted
Posted

Houston; we have a problem!

Take off in the R34 is proving to be quite troublesome at the moment; especially when the ground is wet or has loose materials on it.

The Slip signal comes on indicating a loss of traction, the engine loses power and i basically go nowhere. Now this is happening way too much for comfort - up a hill, off the mark on a flat road, and even going up a wet driveway.

Is there anyway this can be fixed? Is there a way of restoring power to the engine even when there is slipping?

I understand that it is probably a feature installed to stop burnouts, but seriously i just want to get off the mark without someone running up my ass!

Link to comment
https://www.sau.com.au/forums/topic/77530-r34-traction-control-slip-sensor/
Share on other sites
IanH Collaborator

IanH

Posted
Posted

In the short term - Turn the TCS off :)

the TCS compares the speed of the rears to the spedd of the fronts, and if the rears are spinning faster - it thinks you're wheel spinning

HOWEVER

It's very sensitive and, like the GTR's ATTESA, it can sometimes sense if the rear tyre is nearly bald (compared to the front) which makes it look like the rear is spinning faster and BINGO - TCS!

Here's a quick list of the things I'd check

Rear Tyre wear

Tyre sizes (compare front to rears in this tool - http://www.miata.net/garage/tirecalc.html and make sure theres less than 0.5% difference)

satanic Grand Master

satanic

Posted
  • Author
Posted

Thanks everyone for your prompt advice... TCS switch will be experimented with ASAP!!!

As for new tyres? I think i'll stay, my tyres are @ 95% at the moment and they aren't bad...

Anyways, thanks again... will keep updates on the matter.

shonen Grand Master

shonen

Posted
Posted
What toby19 said.  The switch should be to the left of the steering wheel near ur knees.  The power shouldn't cut at all if TCS is off but you will still see the SLIP light flash.

serious ????

Ive NEVER seen the slip light come on when TCS is off........

hmmm.......ill keep an eye on it next time...

satanic Grand Master

satanic

Posted
  • Author
Posted

OK played with TCS switch today and almost bloody lost control of the car... who woulda known that this tiny little switch is what keeps it so tame :(

I guess that either I'm a lead foot or I really don't know the car well enough yet.

The quest goes on...

Abo Bob Grand Master

Abo Bob

Posted
Posted

No offence intended but yes you need to learn your car. I honestly think that skid pan and track days are the best thing for learning your car. You don't have to go so hard you kill it.

Once you get used to more power it's hard to imagine not being in full control with a stock turbo.

satanic Grand Master

satanic

Posted
  • Author
Posted
No offence intended but yes you need to learn your car. I honestly think that skid pan and track days are the best thing for learning your car. You don't have to go so hard you kill it.

Once you get used to more power it's hard to imagine not being in full control with a stock turbo.

Yeah no offence taken... i've had the car for 2 weeks all up so I'm not expecting any F1 championships yet!

Thanks for the advice though!

satanic Grand Master

satanic

Posted
  • Author
Posted
Wise words Bob.

I thought the car was a bit of a handful at first, but now it seems like you'd have to be doing something pretty stupid to lose control running the stock turbo.

Ok, so what do I need to do or where do I need to go in order to test this car out safely?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • JC71
      gauge needle removal

      By JC71 · Posted

      okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...