Jump to content
SAU Community

Recommended Posts

HI

I am seriously considering changing from my 33gts t to a 32 gtr... I am in adelaide and there are not many for sale here. I was wondering if anybody knows of any in yards in adelaide so i can go and check a few out and start to get an idea of what condition they are in and what to start looking for.

Any help would be appreciated.

Regards,

Matt

Link to comment
https://www.sau.com.au/forums/topic/78319-going-to-buy-32-gtr/
Share on other sites

north east road has a few im sure. I cant remember their names of the top of my head but just drive along that rd and you'll see them, cant miss them. Them dealers stand out like a sore thumb amongst the holden, toyota and nissan dealers.

Mainly importers, but due to the massive influx of R32 GTRs the price has dropped significantly......so there would be a fair few private sellers that need money urgently, off-loading their GTRs at a low price. Mind you, expect prices to jump back up considerably by the time the year is out, following the new SEVS rules.

the market is really depressing atm. If you buy from interstate though thre may be difficulties getting it registered in SA, those who have brought there cars interstate correct me if im wrong. Although i know a few who have had no drama's ie duc - iceduck and andy - sir_gtr.

LOL, agreed jas.

I was shopping for a GTR for about 12 months. Until the day I decided to import one under the 15 year rule, I was looking at them priced between 28-35k. Two weeks after I signed up for an unexpected six week wait, the 15 year olds started appearing in the paper. :)

Lucky for you, theres quite a few of them for sale, and you can buy them for anywhere between 18-30k. Because its an old car, Purchase based solely on the condition of the vehicle. The interior and underbody can tell you quite a lot.

Your also lucky, because the flood of 15 year olds has had a signifigant supply/demand effect on cars aged 91-94, and you can now pick up a 94 model for as low as $25k. :)

Its a fact that importing is for the wealthy, you really need to have excess cash sitting around for the just-in-case scenario, and then theres the unexpected time delays involved.

If you look hard enough (check the for sale section) you should find some for about 22-23k in great condition :)

fake400r: What are your motivations behind wanting a 32 gtr?

What motivation do you need? it's a GTR ferchrissakes! The only thing that motivated me in the end NOT to buy one over what I have now was the age factor. But when I drove one i still fell in love! I'd buy one in a heartbeat if I had the money put aside to throw at it when (if?) things went wrong.

Their are many people asking way too much for 89 GTR's. I'm just wondering how many people are actually paying what they are asking or whether the sellers are dropping prices by much.

I totally agree!!! 89 models for 27k- no thanks! Specally when these people were picking them up for around 12-20k. Factor in transport, "compliance" etc: 5k (max).

Pentae could tell us more

When R32 come under SEVS we'll access to more R32 Vspec's and N1's although compliance is about 5k alone

There are some really nice R32's for sale on here couple of Vspec's and even an N1 but check the trading post as well!

But for a R32 GTR- 25k you can pick up a R33 GTR for another 10k.

I believe R33 is a softer more day to day car than the R32 and it is seriously tempting me! It will just take that little bit longer to save but you’ll have a more comfortable car for the day to day grind.

If ya looking for a track car- R32 is for you!

My motivation to buy a r32 gtr? Well i used to have a vl with rb26, turbos, autronic and all the fruit. Much fun and very powerful. However i didnt have decent car to drive day to day (i do about 450km a week) and the vl drained much funds too.

I sold it and bought the r33. It is very nice with trick paint and big wheels, but its almost too nice to drive all the time. Its also not fast at all. Now though i have just picked up a GSR lancer 4wd turbo for the day to day and have more money coming in so i thought why not have a really tough (300awkw) GTR in the shed and just use it to have fun in.

Anyone have a better idea?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...