Jump to content
SAU Community

Recommended Posts

then its got me mc****d what turbo i actually have then .. if its not a rb20 one ..and it doesnt have the markings of a RB25 and its not VG30 turbo of a 300zx..... what in the hell is it off? ..... if anyone can confirm it for me.. id appreciate it ....greatly

matt

  • Replies 316
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Ah shit.

Oh well, I will most likely get them turbo from zoom, as GCG has confirmed it's the right one.

Then it seems that there is NO difference in casting marks or identification between the turbos.

Shite

So reasonably comparable for new, and a bit more than used. Sounds good, comes with warranty so a decent option for those interested.

Ian, I think you are right, but find 220rwkw was too much on stockish suspension so the lod R33 needs plenty to tie the thing down. 280 would be tyre murder :(

Hi Geoff, I've spent more money on suspension than the engine...LOL...Whiteline everything they make for R33 and Bilstein, Strut Braces Front and Rear, Adjustable Caster Rods, Adjustable Upper Rear Camber Rods. And Brakes have been hugely upgraded....Ohh and one of your magnificent Hicas Lock Bars.

Ian

Just to throw another spaniard in the works , there is another exhaust housing by Garrett thats 1.06AAR and twin entry T3 flanged for the TA34 turbos that could work . It has no waste gate so not a straight fit but may work for some .

Cheers A .

So here's what I can figure out.

Stay with me.

RB25DET turbo

OP6 on exh housing

45V3 or 45V1 (series 1 and series 2 or R34 GTT turbos)

RB20DET turbo

OP6 on exh housing

16V on comp cover

VG30DET turbo

OP6 OR V45 on exh housing

16V on com cover.

So, there ya go.

i see what u mean by the exhaust inlet side ..distance.... but can i safely say that its not a RB20 turbo?

Matt

It looks like a rb25 compressor and cover with a VG20 exhaust wheel and exhaust housing.

it is BB. you have an unusual turbo there:)

If its a RB25/VG20 combo it will put out about 215rwkw on an rb20. its exactly what i had on my rb20.

hope that helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...