Jump to content
SAU Community

Trust GREX Shift Knobs...

garage-13
 Share

Recommended Posts

ECR033 Mentor

ECR033

Posted
Posted

Totally understandable, no worries there.

I just wanted to keep the communication lines open as I wasn't sure if my PM's were being sent/received due to the forum upgrade. Alex has been easy to deal with so far, so I'm sure I'll hear back from him in due course :mellow:

MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

ecr033 check that your pm box is not full, because I saw alex today, and he said he tried to pm a couple of people and their pm boxes are full (when the forum changed over max inbox size went from 200msgs to 100msgs

  • 7 months later...
JD-33 Community Regular

JD-33

Posted
Posted
i got an R33, got exactly the same knob. Direct Screw on...

So does that mean that teh skyline gtst gear shaft is a 12mm thickness? i.e. what the trust knob is?

I have read elsewhere that the skyline shaft is 10mm ...

-JD

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...