Jump to content
SAU Community

Recommended Posts

Got myself a set of s2 tail lights and installed them on the weekend. They all work fine and look really good i reckon. Only problem is now i get a light on the dash when i turn the headlights on. Though last night it went out for a little while and then came back on again.

Is that light supposed to come on when your headlights are on? Or what does it mean if it's on?

Also when changing the tail lights, there is a green plug on the same loom as the tail lights which doesn't plug into anything. Anyone know what it's for?

Link to comment
https://www.sau.com.au/forums/topic/80106-headlight-light-on-dash/
Share on other sites

that's an earth, son, the green thing is an earthing plug, i can't really explain where it goes exactly

but here goes,

there is a steel clip which points downwards, it is located towards the middle of the boot, it is concealed beneath the plastics which surround the lights, it should be fairly self explanitory, but i guess it could be a bit tricky just reading this, it's like, up the top of the boot tub, above the light the green thingy clips onto that

if i remember rightly it's more between the centre and right taillight,,,

by the way, S2 taillight are sexy, i now have a grudge against u for not buying my series 1 tailights =-P

having said that, i forgot to plug the green thing in when i did my tailn lights, and the red headlight flashed up, its nothing to be concerned about replicate, it just means they aren't earthing properly,

if this still isn't making sense i spose i can get some pics n post em up but hopefully that should make sense homey,

good luck

aight homey, i took some pics for you, hopefuly it'll make a bit more sense

photos are in succession,

first is back of car, second is the light you look at, third is the view of the light cluster (upside down, as if you were looking at it) then finally, the green loom and where it is located in relation to the light

  • 6 months later...

i know this is an old thread but i have just installed the s2 tailights ....and i get the red headlight symbol on the dash aswell. The only things i unplugged were the lights to take em out and the plug the new ones in. all other cables seem to be fine were left plugged in

replicate did u solve this problem?

and eps do still have the pics of what u meant?

and does anyone else no how to fix the headlight light on the dash

ok if that didnt work it means one of the globes inside the lights is blown, i used to have this problem with one of my lights when i would brake,

you have 2 globes inside each cluster, obviously one of them isn't working, you might need to pull the light panel out it only takes a sec cos it can be a bit hard to tell,

but yeah find out which one is working and replace it, the reason the red light comes on is cos it isn't getting a signal back from the light n it's a cefiro warning system to say one of your lights is out! :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...