Jump to content
SAU Community

need help on what pipes to get.

Bo0sT_JuNkY

By Bo0sT_JuNkY,
in Engines & Forced Induction

 Share

Recommended Posts

Bo0sT_JuNkY Community Regular

Bo0sT_JuNkY

Posted
Posted

im looking at getting a exhaust and i found one at ''unique autosports'' that looks ok

''UAS Trust Copy 3"cat back exhaust, higher flow as does not have a restrictive internal pipe in rear muffler, 20% larger centre resonator, full stainless pipes where Trust is stainless rear barrel only.''

http://202.139.242.57/Images%202/Skyline%2...s/uas%20kit.jpg

http://202.139.242.57/Images1a/Skyline%20p...s%20exhaust.jpg

$995

But its not a jap made so im a bit cautious.

''HKS Super Dragger exhaust for R33 GTS-T. Cat back 3 1/2 inch pipe and 5 inch tip ''

http://202.139.242.57/images/MVC-002F_2.JPG

http://202.139.242.57/images/MVC-001F_2b.JPG

$1495

Is it just me or does this price seem right ??

Well im going to get this for sure :)

Dump and engine pipe in 1

http://202.139.242.57/Images1a/Skyline%20p...0dump%20non.jpg

$550 in mild steel

Link to comment
https://www.sau.com.au/forums/topic/8023-need-help-on-what-pipes-to-get/
Share on other sites
predator Grand Master

predator

Posted
Posted
But its not a jap made so im a bit cautious.  

''HKS Super Dragger exhaust for R33 GTS-T. Cat back 3 1/2 inch pipe and 5 inch tip ''

That is the system I have on mine. Works well, and not too obnoxious in terms of noise. Fairly nice drone from it and it seems to breathe fairly well. Just my thoughts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...