Jump to content
SAU Community

Recommended Posts

Ok here is a list of the parts I have for sale from my R32 GTR:-

Pics below...

R32 GTR radiator in perfect condition (at BEL garage for inspection) $200

oil breather catch tank for any RB with K&N airfilter on top $80

GTR RB26 cams $200

stock dumps $100

front pipe $100

R34 fuel rail SOLD

Nismo fuel reg $100 SOLD

factory ECU $100 SOLD

air flow meters RB26 $70 SOLD

turbosmart dual stage boost controller SOLD

R32 GTR coil packs in great condition!!! $200 for 6

R32 GTR front brakes $1000

(full setup with 1500km new rotors DBA4000 and new pads with reco calipers)

and last of all a set of turbos (GTR R32) (stock) dead! so need rebuilding....make me an offer, as I am sick of fighting to have them rebuilt by the dodgey turbo company involved.... (sure to make them lose the couple of grand they have cost me in bad PR!)

so if you have any questions just PM me ....

it all has to go!!!!

****EDIT****

ALL must go shortly..... some parts being held in NSW some with me going to SA

post-16093-1125937378.jpg

post-16093-1125937458.jpg

post-16093-1125937589.jpg

post-16093-1125937674.jpg

Edited by williamsf1
Link to comment
https://www.sau.com.au/forums/topic/80376-parts-must-go-r32-gtr-plus-extras/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...