Jump to content
SAU Community

Recommended Posts

i was there lat night too, i saw u there RSTME but i didn't come over i didn't know it was your car, next time i will. what happened on the run where your car got tail happy about half track, nice save from the wall anyway. it was a packed night for cars anyway some nice 32's and i'm always a big fan of the rotor's. i go usually every week anyway so hope to see some of you there sometime.

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464388
Share on other sites

I spectated with a mate. Heaps of Holdens and Fords, too many actually ;)

Afew rotors out which is good to see (most likely testing for this sundays bracket meeting). They had a few oil downs in the staging area of 1 of the lanes so that's why the nites racing was slower than normal (along with a massive entry of cars).

The burnout comp was quite good considering the quality of cars.

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464584
Share on other sites

the holdens and fords sucked LOL he he he he they were all so slow....they wish they had a chance against the classy cars ;) like skylines he he he he my friend told me skylines r taxiz in japan :S is that true??

90% of Taxis in Japan are Toyota crowns .

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464670
Share on other sites

plenty of Lines at WSID last night,i spoke to 2 guys,neither came on here,was a r34 GTR with coverd up #plates 'o0OhH!'  

did anyone see ME:) ???  

i had 3 runs  

15.2

20.8  LoL

15.1

full zorst,pod,13psi,Automatic & crap tyres.

I was there with the covered number plates in the 34 GTR M-spec .

Very busy , i had 4 runs all in the 12's with a best time 12.3 @ 113 mph but my stock clutch couldnt hold , my best 60ft was 2.05 .

A silver 33 GTR series I was doing 12.5-12.6 .

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464679
Share on other sites

I noticed you werent launching very hard. Thought you may have been taking it easy for your first time in the new 34 ;)

I launched at 5500 the first time but the clutch wouldnt hold then i backed off , one time i launched at 2500 but the last run was the best 4500 .

GTRS need to be launched at 5500 -6500 to get a good 60 ft

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464719
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...