Jump to content
SAU Community

Water in engine bay.. .

ASYLUM

By ASYLUM,
in General Maintenance

 Share

Recommended Posts

ASYLUM Community Regular

ASYLUM

Posted
Posted

Before anyone laughs no i didn't go washing my engine with a hose or anything ;)

I was driving home last night from my gf's and took the back streets, it was raining very heavily and the streets pretty much flash flooded.

i drove through a couple of large puddles and about halfway home my car started running rough (sounds more like WRX than usual). when i got home i popped the hood and checked out the engine bay - i had a small puddle under my pod filter but not touching and my radiator was wet but apart from that i couldn't find any other signs of water in there.

i know if you get water in your plugs or coil packs your car will run rough but going by the location of the water i don't see how they could get wet.

any thoughts on what else could make it run rough like this and if i should just let it dry out through driving etc or take it to a mechanic and get them to check everything out?

its an RB25DE R33.

cheers.

Link to comment
https://www.sau.com.au/forums/topic/81252-water-in-engine-bay/
Share on other sites
|PRESA| Proficient

|PRESA|

Posted
Posted

I had that problem awhile back and it worried me 'cos it was so close to the pod filter.

Beat me for ages on where this dam water came from every time it rained (even it was a sprinkle) anyway along the engine neat the right hand front quarter panel there are a few holes (just above the pod filter where the bonnet close on top) I siliconed those holes and no water got in any more.

Does that make sense?

ASYLUM Community Regular

ASYLUM

Posted
  • Author
Posted
could it be possible ur intake sucked some water in?

possible yes ;) but i bloody well hope not, it's an Apexi type and i don't think it would have sucked much in there but unsure.

if it has then thats really bad right?

i was doing about 80 at the time on a highway and the lights were out and one whole lane was flooded and it sprayed up and over the car. its happened before but never affected my engine.

might have a bash at water proofing the engine bay too, thanks |PRESA|

might have to check the coils etc when i get home tonight.

cheers guys.. yesterday was just a bad day all up.

ASYLUM Community Regular

ASYLUM

Posted
  • Author
Posted

checked my engine bay at lunch, was all dry.

started it up and it idled rough again, let it sit for a few minutes and it returned to normal, drove it like that for about 5-10 mins and then it started running rough again.

am thinking that the air pod may be wet and sucking in moist air.

SECURITY Grand Master

SECURITY

Posted
Posted

thanks..

you'll need a 16mm deep socket for the plugs, 8mm socket for the coils and the clamps on the cooler piping, pliers for the clamp the oil thing ontop of the front of the rocker cover, and a hexagon thing for the little screws on the rocker cover.

Joe

ASYLUM Community Regular

ASYLUM

Posted
  • Author
Posted
thanks..

you'll need a 16mm deep socket for the plugs, 8mm socket for the coils and the clamps on the cooler piping, pliers for the clamp the oil thing ontop of the front of the rocker cover, and a hexagon thing for the little screws on the rocker cover.

Joe

thanks for the info. much appreciated.

SECURITY Grand Master

SECURITY

Posted
Posted

if u sucked up water in ur air intake it will either seize ur engine, or if there wasnt much it will eventually dry.

the wrx sound is being caused by wet spark plugs.. thats from experience.. i was running on 4cyl :|

Joe

ASYLUM Community Regular

ASYLUM

Posted
  • Author
Posted

ok.. .

i took the coils and plugs out today, also removed the intake etc - no water whatsoever anywhere that i could see.

however i did notice that spark plug number 5 seemed to have some white powder (like you get on battery terminals) on the end that connects to the coil so i thought i'd just clean that of with a bit of steel wool and it should be ok.

cleaned it up and then checked my coils, found that coil number five's spring or coil is no more! it has somehow corroded to nothing, so i guess its been running on 5 cylinders the past couple of days.

fingers crossed oonce i replace it all should be well again.

i called Nissan and was quoted $275 for a single replacement coil!?

don't suppose anyone has upgraded to splitfires and has any old coils in working order lying around? for an RB25DE

one final thing, while i was pulling all the pipes off that are in the way of the rocker cover i think i have disconnected one accidently and do not know where it goes to.

next to the radiator on the right is a small cylinder with 3 pipes coming out of the top, one feeds back into itself halfway down, another runs across the engine and into the intake plenum, the one i am unsure about is attached to the previous pipe and is marked 'purge' at the cylinder. it has a clip on the end so i assume it connects to something else and doesn't just 'purge' into the engine bay?

thanks to all again for the advice.

ben

SECURITY Grand Master

SECURITY

Posted
Posted

just fix your coil... buy a new spring for it, and get a little drill set with a small sander attachment and sand away all the built-up shit on the inside of where the spring goes in the coil. shouldnt cost you much at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...