Jump to content
SAU Community

Recommended Posts

Occassionally, I hear a hissing sound from within the dashboard which seems to be coming from the air conditioning vents. Are there some motors that control the air flow from the vent as I have climate control is my car?

The sound is only there for 2 seconds and then would come back after a few minutes.

Most of the time I hear it while on the Motorway as the car is cruising and there is no music on etc. It is very faint but I am not sure if it is something serious as I am only a 2month old skyliner.

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/83600-noise-from-dashboard/
Share on other sites

There is a motor/actuator that opens/closes the vents when chaning 'modes' try it, change the mode from feet to face to top vent and listen closely (dont need to have engine running)

Yes, I thought it was the case but even when it is set to a single mode and I am not changing it, I can faintly hear the motors. I guess it's the climate control system opening and closing the vents to maintain the set temperature.

Thanks for that, I was just a bit worried that something might be wrong.

:D

There is a motor/actuator that opens/closes the vents when chaning 'modes' try it, change the mode from feet to face to top vent and listen closely (dont need to have engine running)

I've got that problem in my r33. When i turn the car on the ticking noise starts coming from the dash(near climate control), and lasts for few seconds. Change the mode to feet and face it stops it... so it only does it when the mode is to face or the climate control is OFF. What should i look for?

  • 4 weeks later...
I've got that problem in my r33. When i turn the car on the ticking noise starts coming from the dash(near climate control), and lasts for few seconds. Change the mode to feet and face it stops it... so it only does it when the mode is to face or the climate control is OFF. What should i look for?

*BUMP*

My r33 does this also. When you turn the key to the 'ON' position it makes a clicking/ticking noise like TK TK TK TK for a few secs then stops.

My sisters bf tried telling me it was the fuel pump pumping fuel to the engine that was making the noise, but my mate and I decided it was something to do with the climate control (as it made the noise again if you turned the climate control off or changed settings etc).

Is it supposed to be audible (it is easy to hear)?

My r32 Does the same but very Rare

I have it on Face and it goes tick tick tick tick tick, Scared the shit outa me when I first heard it. To stop it I changed it to feet and it stoped, I think its the motor getting Jammed by something or its trying to go lower then it is able. But i know its not a good thing, If you can hear a whine yes it the vents doing there job shouldnt be overerly loud tho, Might need re-greasing.

Guys, the sound coming from the dash that sounds like little motors are normal. They control the set temp from the climate control. You will notice this sound when manually adjusting the temp on the climate control. This is not a problem.

The ticking noise comes from the winscreen demister vents. When the car or climate control system is turned on, it goes through a vent check. The connectors to the vents on top of the dash, aiming at the windscreen are known to dislodge and when they are activated to open/close the vents, it clicks. This is a problem and the only way to fix is to pull out the dash. This is not worthwhile fixing as after a while, it will dislodge again. This ticking sounds occurs in all Skylines I've been in...

Hope this helps. B)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
×
×
  • Create New...