Jump to content
SAU Community

Recommended Posts

hi guys,

ok let me paint a picture,

i have a 33, with some mods, and makes some power,

i have a bosche 040 supplying fuel to standard injectors with a stock pressure reg

this is my second bosche pump (will explain in due course)

after about 100kms of hard mtn terrain in the crisp hrs of teh morning, the pump gets very noisy and the car starts to miss.

i stopped and pulled teh pump out,

no signs of anything blocking it, mesh looked nice and clean.

however i did notice that all the fuel in the tank was rather warm, heaps warmer then fuel normally is.

anyway, put the pump back in, filled up with gas and drove on,

about 40 kms further along the drive, same issue started up again. car starts to miss under load, and even at very low revs,

cars becomes completely undriveable

wen i stop the car i hear the very noisy pump whinning like a virgin being broken in by a big black african warrior.

once the pump cools down (i ssume its cooled down casuse the noise stops) it starts to work fine again.

so what do i do?

get another pump, (i sent the last one back when it started to do this)

or is it something else?

any ideas and comments will be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/
Share on other sites

I recently got an 040 installed intank in my 33 GTST, to replace the stocker.

Only issue I had is that I couldn't get the pump as far down as the standard one (due to the design of the pickup), but I've got no problems with that because I'm able to keep my car filled to at least a 1/4 tank at all times.

Apart from that, you wouldn't be able to tell it's an aftermarket pump. No extra noise, the car doesn't take any longer to start, and I'm totally happy with it.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521108
Share on other sites

neil: sounds like its not getting enough current, therefore not working to its full efficiency. Probably the heat is the sign of it working much harder than it should (which like u say will result in a failure eventually)

might have to run some thicker cabling to the pump..

Something to investigate anyhow.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521490
Share on other sites

mate.i had a similar problem,sounds to me that you have a fuel block,first i would look at your fuel reg pressure,cause of this means if it is blocked or not functioning properly means no fuel is returning back to tank.at this stage fuel pressure is building up in your fuel rail sending too much fuel thru your injectors which floods the spark plugs causing miss.I suggest checking fuel pressure at in take and return.Its happened to me,also happens after 20mins of driving with same symptoms.In my case it was the fuel reg.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521711
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Omg Brake pedal removal.. FML!!
    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
×
×
  • Create New...