Jump to content
SAU Community

Recommended Posts

Hi guys/girls,

A strange thing happened to my car today which has caused what I believe the alternator to die on me. What happened was this morning was that I took out my battery to use it to start my brothers car (nothing out of the ordinary) and placed it back into my car and it started fine. Drove it and then when I went back to the car after a few hrs to start it, I noticed that the alternator was still ticking over when I had started the engine. Even when the ignition was placed to the On position it still keep turning over, taking the keys out still had it going.

So I started it again and it seemed as though the sound had gone but not long after I was driving it, I heard a squeeling noise which I only picked up not long after the rain has cleared but by then I saw smoke coming out of my engine bay and that was when I suddenly lost all my power. Popped the bonnet and a strange smell was coming from the alternator. Now im assuming that is dead/going as I could not start the car at all, only managed to get it started by pushing/1st gear clutch starting it. Once I got it home, it now starts but struggles alot and the same strange smell is coming from the alternator region.

Sorry for the long post but just though Id explain in detail what happened.

I just called a local auto electrician and they quoted a couple of hundred for a rebuild ;) while an importer said $140 - $150 for a 2nd hand one. BTW all alternators on r33 gtst's are the same, right?

more then likely they are all the same. Have you had a look at the wiring and plugs from there and around it. You said there was a ticking sound, i didnt know alternators made a ticking sound. You sure you arent referring to the starter motor that was ticking away?

Drove it and then when I went back to the car after a few hrs to start it, I noticed that the alternator was still ticking over when I had started the engine. Even when the ignition was placed to the On position it still keep turning over, taking the keys out still had it going.

To me it sounds like your describing the starter motor...the alternator should be turning with the engine running, but the starter shouldn't.

more then likely they are all the same.  Have you had a look at the wiring and plugs from there and around it.  You said there was a ticking sound,  i didnt know alternators made a ticking sound.  You sure you arent referring to the starter motor that was ticking away?

No havent looked at the wiring and voltage around there yet. Yes, that correct when I first when to start the car there was a continous ticking sound even though I got the car started (as though was stuck on START). realising this I turned off the ignition and pulled out the keys but keep going.

To me it sounds like your describing the starter motor...the alternator should be turning with the engine running, but the starter shouldn't.

At the moment when Im starting the car I have it give it some throttle for it to start but it seems as though it wants to die on me when doing it though. Besides, once started there is a strange smell coming from the alternator region (smells like burnt electrical things) much like the same smell when the engine just shutted down and smoke coming out of engine bay when I was driving although not as strong.

Since you two suspect its the starter motor Im numb folded as to which of the two component is actually is now as Im just describing as I see it.

Hey Nozila, as they have said an altenator is driven by the engine, a starter drives the engine :P

Now I have seen starter motors lock in mesh (when they engage the ring gear) and what happens is they usually flare all the windings and are unrepairable if the engine continues to run with them engaged.

An altenator will not cause a car to keep trying to start even after you pull your keys out of the ignition. This problem can be a multitude of things, right from the electrical switch on the back of your ignition barrel, or a problem in the starter.

I have seen the copper contacts weld together in a starter motor from trying to start with very very discharged battery.

Its process of elimination mate, I wish I could help you more - but I live in North West NSW - in the bush :blink:

Cheers

Sumo

That smell you can smell is what we call at work the "dollar smell", coz you know its going to cost alot of dollars to repair :P

Sorry about me making a joke, if you handy with a spanner, pull your starter off and smell inside the nost cone, if you can smell the "dollar" smell go and get a second hand one :blink:

Cheers

Sumo

Sumo, thanks for the advice I will do just that. Unlike earlier today when the car didnt want to start at all, it now does but struggles to turn over needing the help of throttle action. Say i wanted to check the voltage on my alternator though, would i just measure the lead that is coming out of it from the back and what voltage should it be?

thanks,

duc.

the alternator sits basically in front (towards the front) of the starter motor, and its easy to think one is playing up when its the other.

I cant remember exactly, but there is a power feed going from the alternator directly to the starter solenoid.

It sounds like the starter solenoid (the small round part on top of the starter) has shagged it, and may be playing funny buggers with the alternator (due to its direct feed from the alt.)

Ive got a spare starter motor here you are welcome to try, and if it sorts your problem, you are welcome to have it for $50 :blink:

Its an easy job to get the starter out too...2 bolts, and 2 nuts....oh and a skinned knuckle or 2 :P

Use a multi meter to read the current coming out of the alternator at idle. Put hte positive lead on the cable coming out of the alternator and put the negative lead on an earthing spot. You should see about 13-13.8 volts at idle.

Hope this helps,

Deren

I just went outside to start the car and check on the voltage. Car still struggles to start but does, i measured the voltage (using a multimeter) from the lead going into the alternator (red plug over the lead) and it showed 14.5v which means that its charging the battery and thus isnt the culprit, I assume? Also, does anyone know that when my engine suddenly lost all power that it may have an adverse effect upon the engine?

Well it is high but i cant see that being a problem. Make sure all the cables an conections to and fromt he battery are all good. I had a simialr problem once where the car would just die and it was the terminal on the battery. If you have msn add me there id be happy to help more [email protected]

I can rule out the battery being dead/drained which has caused the car to stuggle when starting. As I disconnected the battery and charged it for a good few hours, whilst I was at it cleaned the battery tray/terminals, but it seems the car still struggles to start. Starting to narrow it down, 1 down 2 to go.

14.5v is fine for a cold start, once everything warms up voltage will drop to high 13's maybe flat 14's.

The regulator is designed to feed more voltage in to the battery when it is cold rather than when everything has warmed up. Its apparently the way battery's like to be charged, less volts when warm, more when cold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...