Jump to content
SAU Community

Recommended Posts

Although the value at which it flashes can be set..

I used to think my knock levels were okay.. then I've seen 90% of people have lower knock readings than me ;) Time for a retune..

i think the knock on the power fc is a load of crap simply because if u go over a bump or pot hole or the road isnt the greatest --(NSW ROADS) the knock level will b all over the place. if u want to be accurate u would get an exhaust temp reading!... my 2cents worth!

i think the knock on the power fc is a load of crap simply because if u go over a bump or pot hole or the road isnt the greatest --(NSW ROADS) the knock level will b all over the place. if u want to be accurate u would get an exhaust temp reading!... my 2cents worth!

I dont think understand how the knock system works ,it's looking for more like harmonics then just bump your a knock to the car. And yes they do work very well or why would a cars like Keir wilsons retain the power fc and hand controller when his running a full metec system (knock detection).

As for knock levels well i think to many people get carried away with the levels as every car is different especially car run fordge pistons and lump cams etc

BUT just concide this that APEXI and i believe nissan don't think there a real issue to you get around 60 knocks as that is when they fire the warning light (not before all they would have set the level lower) all that said most responible tuner will normally stay below 40 or so to give a bit of head room for a bad datch of fuel and or different weather condition to the day of it,s tuning.

pete

I dont think understand how the knock system works ,it's looking for more like harmonics then just bump your a knock to the car. And yes they do work very well or why would a cars like Keir wilsons retain the power fc and hand controller when his running a full metec system (knock detection).

As for knock levels well i think to many people get carried away with the levels as every car is different especially car run fordge pistons and lump cams etc

BUT just concide this that APEXI and i believe nissan  don't think there a real issue to you get around 60 knocks as that is when they fire the warning light (not before all they would have set the level lower) all that said most responible tuner will normally stay below 40 or so to give a bit of head room for a bad datch of fuel and or different weather condition to the day of it,s tuning.

pete

okay i was thinking that knock is the knock inside the engine right as u explained the harmonics well that can change quite rapidly esp if u have hard engine mounts and suspension....is this right ...?

i looked at my knock after going over a bump in the road and it changed...? so in other words it is not an accurate reading at all since it did affect the harmonics in the engine....? and therefor it might not be reading the harmonics in the engine but actually the shock from the bump...?

something on your car is f**ked mate if bumps in the road cause a knock reading. I always monitor knock in my car and it is never affected by road conditions. never. and i will include in this burnouts, drag launches, 4 track days and a fair bit of street driving.

exhaust temp reading is really only a good measure of engine effeciency/AFR and is not as quick to react as a knock meter. they are two completely different things for completely different purposes.

something on your car is f**ked mate if bumps in the road cause a knock reading. I always monitor knock in my car and it is never affected by road conditions. never. and i will include in this burnouts, drag launches, 4 track days and a fair bit of street driving.

exhaust temp reading is really only a good measure of engine effeciency/AFR and is not as quick to react as a knock meter. they are two completely different things for completely different purposes.

ahhaaahah thats a laugh!

so u dont get any knock when going in a pot hole.....?

i find that hard to believe since the vibration is carried through the car...mmmm

but anyways each to your own and ill tell u one thing just had the engine rebuilt ...so its not f**ked!...lololol

im just saying that is not accurate the knock on the power fc.

so u dont get any knock when going in a pot hole.....?

i find that hard to believe since the vibration is carried through the car...mmmm

no i don't unless you are talking about a 3 foot deep cavern (which i can't comment on as i've never driven into one). I have been in potholes before, and a couple of times gone offline a little at turn 4 oran park (big bump there) and yes the knock reading didn't change.

I never said your engine was f**ked i said: "something on your car is f**ked" it may be gearbox problem sending a shock through the crank, or a faulty knock sensor, or knock sensor wiring, or it may just be a shit tune. but i can tell you no car i have ever been in has the knock reading affected by bumps in the road...

no i don't unless you are talking about a 3 foot deep cavern (which i can't comment on as i've never driven into one). I have been in potholes before, and a couple of times gone offline a little at turn 4 oran park (big bump there) and yes the knock reading didn't change.

I never said your engine was f**ked i said: "something on your car is f**ked" it may be gearbox problem sending a shock through the crank, or a faulty knock sensor, or knock sensor wiring, or it may just be a shit tune. but i can tell you no car i have ever been in has the knock reading affected by bumps in the road...

ok ok ok im not going to start answer this if u go over a pot hole or hit the ripple strip at the track and u feel it im sure your engine will feel it....

it may be due to my hard suspension and engine mounts and all the other siffening ..hahah

but im going to argue.

okay i was thinking that knock is the knock inside the engine right as u explained the harmonics well that can change quite rapidly esp if u have hard engine mounts and suspension....is this right ...?

i looked at my knock after going over a bump in the road and it changed...? so in other words it is not an accurate reading at all since it did affect the harmonics in the engine....? and therefor it might not be reading the harmonics in the engine but actually the shock from the bump...?

no that is not right

you need to open your eyes a little and think

If yours is doing this, dont just say the pfc is crap and the knock detection does work may you should be asking why is mine not working (because i can safety tell you that they dont all do what your does) and the knocks and haromics dont have to come from inside the motor as i have seen a exhaust touching the chasis effect knock reading before,(your could be as simple as this).

The knock detection system of the std gtr with apexi pfc is one of the single most helpfull tools in tuning the car a tuner can have(trust me i have know tuned a few).

pete

The reason I asked this question was becuase I have just added a power FC to my GTR and the tune is (out of the box) I was told that they have very advandce timimg so I did a dyno run with results of 11.5 A/F and a knocklevel of around 20.

Was told by a Melbourne PFC tuner that anything around 50 to 60 was bad.But then I was reading in PFC FAQ and it said that anything more than 10 was bad.But it sounds like 10 is a bump steer <_< so all is good B)

Thanks

no that is not right

you need to open your eyes a little and think

If yours is doing this, dont just say the pfc is crap and the knock detection does work may you should be asking why is mine not working (because i can safety tell you that they dont all do what your does) and the knocks and haromics dont have to come from inside the motor as i have seen a exhaust touching the chasis effect knock reading before,(your could be as simple as this).

The knock detection system of the std gtr with apexi pfc is one of the single most helpfull tools in tuning the car a tuner can have(trust me i have know tuned a few).

pete

i found my knock sensor was f**ked sorry guys!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...