Jump to content
SAU Community

Recommended Posts

Hi,

I have taken the standard headunit out of my gtr to find a mess of wires behind (from a previous stereo). My problem is that when i test each of the wires for a battery wire I don't find anything with the digi meter.

Going by standard Nissan Wiring it should be black w/ red stripes but these provide nothing (I found 2 ??).

I checked all the fuses under the steering column individually and they are all fine.

Any ideas at all?

TIA Jon

Link to comment
https://www.sau.com.au/forums/topic/85476-help-with-head-unit-install-query/
Share on other sites

blk/red is the antenna trigger. are the factory plugs still on it?

you should have 4 twisted pairs of wires. these are front and rear. the gtr has that annoying amp in the rear shelf that should have been bypassed already.

red/blu is lights , should be a blue/? one that is +12v key and the other one should be a red..

( haven't worked on a skyline for a few weeks so I can't remember the colours.)

if the plugs are still on it buy an adapting plug and use that. makes life easier.

Thanks for the quick replies.

The factory unit was working when I removed it

The original plugs are all gone.

I will try and investigate further now.

After testing every wire I cannot find a +12v battery, what other things could I try?

worst case senario you could always just run a new wire from your battery..

.. have you been able to measure 12v on the ignition and lighting leads? might sound silly, but are you sure you have a good ground for your multimeter?..

cheers,

damo

You sure your using your multimeter correctly? You'd wanna have it on the 20v setting, then be testing each wire with your red probe, whilst always having your black probe grounded (could use your earth wire for the HU if u know which one it is, or the cigarette lighter, or even the headunit chassis is usually earthed also).

Best of luck,

Nasha

there is 12V memory there. you have a blown fuse. do a physical check ( remove and inspect.) every fuse. you shouldn't have an interior light currently. the fuse you are after should be outside.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The boot notch on the GK Tech rods is different to OEM yes. You'll find a solution. They are a good rod, I have used many of them for various setups, and no they are not ' just for drift cars', they are fine as an OEM replacement. Same goes for the tie rod ends although I found they transmitted a huge amount of NVH a normal balljoint masks, making it feel like there was something loose or knocking, even though there wasn't. If you used the same pieces on each side, no reason one angle should be different to the other side. Have you checked ride heights/measured the angles? Or just visual? Your alignment will be massively out of whack yes. Up to you; it is worth taking the time to learn wheel alignments and do it yourself. I have never had better wheel alignments and I haven't taken my car to a shop for, dunno...many many years. Spend a few hundred on equipment, do alot of research via online articles, youtube vids, and "trial and error" on setups. Eg, set it with too much toe-out, toe-in, too much or little caster, drive the same stretch of awesome twisty mountain road each time, learn how they feel and how the car's handling has reacted to your changes.
    • Won鈥檛 be hard to beat them. 馃ぃ Farken sponge cakes!
    • Nah I did not will have to another time. I only installed a blitz return flow FMIC probably 1000kms ago. When I took the old piping off there was basically no oil in piping. At this stage it has to be valve stem seals. When I roll down a big hill in gear and then throttle down the bottom, I get the same puff of smoke.
    • I believe when they added coolant to cool the turbo it negated the need for turbo timers as water continues to flow even when the engine is shut off I forget the actual terminology, I'll just say the coolant "percolates" through the turbo which stops the oil cooking itself to death  Well....that's how I see it, as all the plant at work that has coolant lines to the turbo can be shut down straight away, whereas the older plant with only oil feed to the turbo you need to idle it for a few minutes
  • Create New...