Jump to content
SAU Community

Any Comment? Good Or Bad?

siaw

By siaw,
in Western Australia

 Share

Recommended Posts

siaw Explorer

siaw

Posted
Posted

Hi all, my car somehow accidently make a 180 spin and after that, I realize a few diffrent from before. When the engine startup during cold weather, it start at 2k rpm, b4 that was 1k only. But it then slowly go down to 600-700rpm. Before it make the spin, max RPM during startup is 1k and normal running is 500 only. Not to mention, my Apexi turbo timer "DEAD", no information been display. My best guesses is the ECU somehow auto reset! Anyone have any comment on it? Is this good or bad?

Link to comment
https://www.sau.com.au/forums/topic/85727-any-comment-good-or-bad/
Share on other sites
Kaido_RR Grand Master

Kaido_RR

Posted
Posted
Hi all, my car somehow accidently make a 180 spin and after that, I realize a few diffrent from before. When the engine startup during cold weather, it start at 2k rpm, b4 that was 1k only. But it then slowly go down to 600-700rpm. Before it make the spin, max RPM during startup is 1k and normal running is 500 only. Not to mention, my Apexi turbo timer "DEAD", no information been display. My best guesses is the ECU somehow auto reset! Anyone have any comment on it? Is this good or bad?

its Highly unlikly that the spin did anything to your car,

It is normal for your car to rev at higher rpm on the cold start aslong as the rpm drops once the car is warm up then you shouldnt worry about it. Normal idle rpm is around 600-800rpm

For your apexi turbo timer, im guessing that the spin may have knock it around and it is possable that the wiring was loses and the spin just knock it out of place, check all ur wiring and make sure everything is connect and grounded right.

Also there is an idle screw on your car, and if ur worried about ur idle just play around with it till u get it to what it was like

Hope that Helps

-Michael :D

siaw Explorer

siaw

Posted
  • Author
Posted
hahaha

did you hit anything? cus really spinning shouldn't do shit.

I'ts my freaking lucky day! There wasnt any vehicle or anyshit on all 4 lane...it just spin out...ntg been hit...by the way, the engine die after the spin, took me 10 sec to start the damm engine!!!

Kaido_RR Grand Master

Kaido_RR

Posted
Posted
I'ts my freaking lucky day! There wasnt any vehicle or anyshit on all 4 lane...it just spin out...ntg been hit...by the way, the engine die after the spin, took me 10 sec to start the damm engine!!!

did ur car die cuz ur didnt put ur foot on the clutch ? i have had a spin and the reason my car die was i had one foot on the brake and forgot about the clutch

Lozzle Proficient

Lozzle

Posted
Posted

What Mike said bout the idling is right, the revs will drop as the engine warms up. "Slowing" to 700 is alright. That's where mine sits at after warming up.

Also agree you probably stalled the car by not clutching in.

Your car would be fine, sounds like rattled wires on ur TT or something.

How did your 'car' accidently 180 itself....?

Steve Grand Master

Steve

Posted
Posted

Jeez its a tough crowd in here (some), the poor guy is obviously from os, and he gets slammed for not speaking english, his grammer isnt the best and he gets canned for that.

What ever happened to the friendly forums? :O

"my car somehow accidently make a 180 spin " siaw, just so you know next time, to write this using the correct aussie grammer, try this:

"I farked up coming out of a bend, put my foot in a bit too hard and the back end went out, after a bit of tank slapping, I lost it compeletly and she did a 180"

Its ok, I know I have farked up heaps driving my car, especially when I was a young fella - probably why P platers have such a high mortality rate :D Dont feel too bad about being honest when you fark up, we all do it, its one way to learn.

Glad to hear there was no accident, you did get lucky there.

siaw, suggest, (as others have) it has something to do with the TT, check all the wiring, if that doesnt work, also check your inlet piping, you may have a small leak near the manifold as some pipes on these cars can be a bit old and tired. Also, as suggested, you could try adjusting the idle control valve, but this is more a cover up than a fix.

If you live near willetton, drop me a pm and you can come around to my place and I will have a look for you to see if it is something obvious, or, if all else fails, just take it to a reputable workshop such as C-Red, Hyperdrive, X-Speed and ask them to take a look.

good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...