Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

new toy for u rev

http://www.takakaira.co.jp/performance/bee...editedBlast.avi

What is REV LIMITER?

The unique REV LIMITER from Power Builder Bee Racing is a device where a driver can use to prevent a vehicle's engine from being over rev. All parameter adjustments on this device can be made on the fly from the driver's seat. This REV LIMITER is achieved by cutting off the ignition at a preset RPM limit, and by re-routing a fuel dump. An aural feedback of back fire popping sound from the exhaust muffler is the result followed by a fantastic visual of fire coming out from the exhaust muffler tip. This aural & visual feedback are very similar to those experienced in the fully race-tuned race cars .

Is it really safe to use REV LIMITER?

The rev limiter in the vehicle is controlled by the factory ECU by instructing the fuel pump to immediately stop the fuel supply to the engine. Such immediate forced fuel cut is not advisable if it happens frequently as it has damaging effects to the engine in the long run. On the other hand, with Power Builder Bee Racing's REV LIMITER, it actually cut off the engine ignition without stopping the fuel supply to the engine. With this function, over rev limit damage to the engine is prevented, and is a safer way in the long run when the engine is over revved past it recommended RPM limits.

Can I install by myself?

The REV LIMITER device can be DIY installed. It has four wires of different colors that needs to be connected to the vehicle's ECU. Please refer to installation manual for detail instructions.

My car using POWER FC. Can I install this REV LIMITER?

A earth grounding issue has to be resolved if a vehicle is fitted with an aftermarket APEXi Power FC unit. This grounding issue is due to a lack of a ground terminal in the APEXi unit. The REV LIMITER uses the ground signal to cut off the ignition signal from the ECU. Since APEXi Power FC is a piggy back computer, and manipulates the original engine parameters' signals from the ECU before re-routing these modified signals to the vehicle individual engine components, a separate grounding signal is required from the APEXi Power FC. Once this grounding issue has been resolved, the REV LIMITER will be able to function as it is intended to be.

When can a car get the effect of back fire with popping sound from the exhaust muffler?

The visual effect of having fire spitting out from the exhaust muffler every time there is a rev cut when the REV LIMITER is installed is not guaranteed by Bee Racing. This is due to the fact that fire would only result during high engine revving, and when the exhaust muffler is warm up, and also when the vehicle exhaust system is without a catalytic converter. Basically, the unrestricted vaporized fuel supply when ignition is cut off is lighted off when it mixes with the air from the engine air intake in the hot exhaust system. The hot temperature from the exhaust system is the catalyst that ignites the air-fuel combination in the absence of the ignition sparks.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...