Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by GTS-t VSPEC

You want to be a navigator? Do they get paid or do it just for fun?

See'ya:burnout:

Paid ??? hahahaa

No , just for fun , glory and Trophies.

btw , the trophy for 2nd o/r at Wellington was a big GT3 porsche. Bugger !! no F1 car.

Cheers

Ken

Would appear that Steve ( SST ) and Mr winfield look alike Gray in the GTST had a bit of falling out.

Was speaking to Steve and he said that a smaller turbo was fitted cos Gray was blaming that.

Cheers

Ken

ps Wholagan is still waiting for steel forks for the ppg box.

Originally posted by GTS-t VSPEC

Did you see AJ drive today? He didn't get to do many laps.

Who's second in 4WD? Seymour?

See'ya:burnout:

Supposedly has 450hp atw but doesn't seem like it. Is the JUN engine but with a supercharger.

Engine was getting hot so AJ parked it. I would too knowing the cost of that motor.

Cheers

Ken

Yeah, I spoke to Steve a fair bit, won't go into details on what he thinks of Gray:D His little Datto was doing alright for it's first run.

Steve Maitland was going well until he went in too deep on the last lap.

Spoke the Graham Stones, his car was flying, but has got gearbox problems.

See'ya:burnout:

Originally posted by GTS-t VSPEC

Yeah, I spoke to Steve a fair bit, won't go into details on what he thinks of Gray:D His little Datto was doing alright for it's first run.

Steve Maitland was going well until he went in too deep on the last lap.

Spoke the Graham Stones, his car was flying, but has got gearbox problems.

See'ya:burnout:

Caratti made a few enemies when he had a coming together with Anderson ( Racetune prepped Escort ) and Matt Cherry in the red RX7 that hit the wall.

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia body...
    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
×
×
  • Create New...