Jump to content
SAU Community

Recommended Posts

Originally posted by XRW

there not allowed to

bottled water is meant to remain exactly that, bottled, lid and all..

its against the health act for them to sell it to you with no lid and opened.. as it possible its been tampered with..

if they give no lid demand it..

they can take the lid off in front of you and give it to you. same principle applies to beer.

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

never been a big "smoker" the only effect i get on it apart from feeling extremely dumb is extremely horny ..... which aint such a bad thing :D

i leave work 3:45 get home 4:30 a go :(

Cams to go in wasnt it?

yeah thats the thing with Skylines take the normal cost for a non-import .... double it tripple it and there you go!!

As soon as you ring anyone for advice or parts enquiry you get "Oh because its an import blah blah blah going to cost more" I swear they see dollar signs in their eyes!

yeah my cams buggered and i think i have stuffed a few valves...

but won't know until i take it apart.

works out good in a way as i will be respraying my engine pay, chroming numerous engine bay parts so will look all nice a pretty once i get a few other problems resolved on the market she goes :D

yeah would liek to give my engine bay a clean up ..... just i know that once i start pulling things apart i wont be able to get them back together :D

And my dad doesnt have too many tools either soooo i'll just leave it with sand all in it. LOL there was this massive storm one day .... and i got caught driving thru it ... anyway i was at a set of lights and there was a construction lot next door and the wind picked up all the sand from the yard and dumped it all over my car ..... and now ive got yellow sand in the engine bay .... as someone said .... it looks like a bloody beach in there!!

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...