Jump to content
SAU Community

Recommended Posts

yeah well i was trying the mind over matter approach paul but you just shot that idea down ;) haha ..... yeah i know ..... parents huge minus.... lack of freedom minus ...... free rent, free internet, heated pool and spa and pets allowed is a huge plus tho ....... its a lose lose situation stay or go but i think i'll just save and start buying bits n pieces and get myself organised ;)

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Morning yall. Not a good 1 though.

So im lying in bed last nite and i hear a car alarm go off. I figure since the4 parents have friends around its gonna be one of them drunkenly stuffing up and making theirs go off.

I get up in the morning and hit the immobiliser when the key is in theon position as u usually do. The engine cranks over but it wont fire :confused: i look at the little batt, parkbrake lights etc and they are all off. The imobiliser is clicking on and off indicators flashing but no dice. I keep cranking it like the moron i am then get out, the fuse in the immobiliser is fine. I disconnect the batt and push the brake for a bit which only reset my clock and didnt do much else.

Any ideas cause i hate paying sparkys

i want pillar mount .... you know the one that fits on the pillar in nice casing ...... i dont want this huge dial sticking out in the middle of god knows where ...... one like yours paul.

But also saying that i dont want to spend a ridiculous amount on a phucking gauge!

Damn Boosty!! ;)

Paul no rush - might as well leave it til i get the veilside on and the car is once again fulltime mine!! and no i havent seriously started job hunting yet.

Aidiwn ..... you need intercooler etc to safely crank up the Boost .... which i dont have .......yet ;)

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...