Jump to content
SAU Community

Recommended Posts

i got a r33 gtst with fmic, cat back exhaust and a pod filter

im lucky to get more than 250 on afull tank of vortex 98 driving slow!!!

ive changed the o2 sensor but that doesnt seem to have worked :S

also bought a new afm

any ideas???

I had a similar prob where my car was just sculling fuel, its cos of the standard computer. I got a fuel controller and had it tuned and it fixed the prob, now a full tank lasts me ages. It not only uses less fuel but i get more power aswell due to leaning out of the mixtures. Get an SAFC or PFC or similar this will fix your prob. :(

yeha the fuel adjuster seem the way i wnat to go, but 250 is wayyy to low :S im certain that my afm is good, and i changed the o2 sensor!

im worried if i tuen it and reduce the ratios the computer will do somehting stupid like run lean and ping!!!

but the car aint worth having if i get 230-260, thats trash! a pushrod v8 gets better than that! and vortex 98 is 98ron so it should be similar to bp ultimate and the car sems to run rich.

might be a stuffed cpu but its all good. im almost finished building a jaycar fuel adjustor and will install and dyno it soon. ill keep u guys upto date with what happens

yeha the fuel adjuster seem the way i wnat to go, but 250 is wayyy to low :S im certain that my afm is good, and i changed the o2 sensor!

im worried if i tuen it and reduce the ratios the computer will do somehting stupid like run lean and ping!!!

but the car aint worth having if i get 230-260, thats trash! a pushrod v8 gets better than that! and vortex 98 is 98ron so it should be similar to bp ultimate and the car sems to run rich.

might be a stuffed cpu but its all good. im almost finished building a jaycar fuel adjustor and will install and dyno it soon. ill keep u guys upto date with what happens

Vortex is 95 octane

i got a r33 gtst with fmic, cat back exhaust and a pod filter

im lucky to get more than 250 on afull tank of vortex 98 driving slow!!!

ive changed the o2 sensor but that doesnt seem to have worked :S

also bought a new afm

any ideas???

Try cleaning the hot wire in the inlet just down from your pod. The oil that you put on the pod[ K&N or my Unifilter] coats the hotwire and insulates it so the ecu thinks it needs to pour the fuel in.I use CO contact cleaner and gently use a cotton bud to do it.

It shouldnt be running so rich and using so much fuel. Just buying a fuel adjuster is masking the actual problem. Have you tried an ECU reset? You should also try an ECU diagnostic as one of your sensors may be playing up.

thats exactly what im thinking!! i dont wnat to amsk the problem cause itll come back to haunt me!

dude what is the hotwire ur talking about? cheers

It shouldnt be running so rich and using so much fuel. Just buying a fuel adjuster is masking the actual problem. Have you tried an ECU reset? You should also try an ECU diagnostic as one of your sensors may be playing up.

thats exactly what im thinking!! i dont wnat to amsk the problem cause itll come back to haunt me!

dude what is the hotwire ur talking about? cheers

Bazz. The hot wire tells the ecu how much air is flowing through the metering system.If you take the pod off [there is probably a mesh cover in there]and look down the induction tube you will see a brass spigot with a large slot cut in it. This brass spigot comes through the side of the tube and a six or seven pin plug goes off into the wiring loom. The way hotwires work is there is a current ,known to the ecu through the small resistance wire. As more air flows over the hotwire it cools therefore to keep the known resistance more power is sent to the hotwire.This is how your ecu knows how much air is flowing through the motor, so therefore the ecu changes the fuelling[pulsewidth and duration] to suit. The lambda sensor does a similar job in the exhaust.

ohhhhhhhhhhhhhh the hotwire in the afm!!!!! yeha dude i did that already. i did a once oiver on the o2 sensor wire anmd some of it looked like it was in bad nic, so i changed it and wala!!! did 100km on first qurater :)

so basically guys if ur running rich this is what worked for me

1)reset the cpu

2) change o2 sensor (or if its fairly new clean it with contact cleaner ~$7 at dicksmith) and reset again

2) make sure all the elads to the o2 sensor are healthy!

3) clean the AFM with contact cleaner and reset again

4) use bp ultimate :O

this worked for me. my next step would have been to put the car on the dyno to see that the other sensors are healthy and that the cpu maps are good!

anyways thanx for all the help

cheers

Edited by bazz

i got the o2 sensor from repco. the direct fit (with the EF plug) cost me $82. i used a pipe socket to remove it, or you could do it with a spanner (21 or 22 cant remeber exactly). i did it myself (and i know nothing about cars). the brand they gave me was ACA. it had a blue wire and 2 black. using clip connectors i put the blue to the big brown wire on the car (r33 93model) and the other 2 are just heat so doesnt matter. then u reset ur cpu and its all good

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...