Jump to content
SAU Community

Recommended Posts

Hi guys, have just joined this forum.

Currently, I own a 1997 TF Magna Sedan, nicely done up looks very tidy.

I'm looking at selling it, and picking up an R33 GTS-T Series II M-Spec.

I want one in pretty much stock format, maybe mags and lowered at most.

I've been doing my searching, and am budgeting 18k or so, max. Alot of them are going for well over 20k though, and some as low as 16k (with 60,000km's average).

What sort of price range should I look at, where should I look and what basic checks should I make as to avoid any common problems with this particular model?

I'm 19, located in Eatons Hill, QLD.

Thanks for any and all help.

Link to comment
https://www.sau.com.au/forums/topic/89376-help-buying-an-r33-gts-t/
Share on other sites

hmm price range anywhere between 18.5k-22k including all on road cost/insurance etc etc..

trying searching it on carsales or in the for sale section on this forum and see if you can pick up a local one. If you dont ilke any of them, then i guess you can import one..

gd luck..

Best tip: Search around and be ready to pay a little more than you budget for..

hmm price range anywhere between 18.5k-22k including all on road cost/insurance etc etc..

trying searching it on carsales or in the for sale section on this forum and see if you can pick up a local one. If you dont ilke any of them, then i guess you can import one..

gd luck..

Best tip: Search around and be ready to pay a little more than you budget for..

I've budgeted 18k for the car itself. Rego, Insurance, Stamp Duty etc is seperate and I've budgeted for that also (all insurance quotes together ready for purchase etc).

It's just a matter of finding a nice, clean low Km M Spec Series II for under 18k (18k is my limit).

you want to find a local one or import one??

there are so many on carsales.com... suggest you check it out..

or try searchin here dude.. so many skyilnes for sale..

Local for sure. I know way too many people who've had issues with importing, mostly wound back odometer... I know one guy who bought the car, and when it arrived it was a different colour entirely... he ordered a black one, and it came in burgundy. Broker was not held accountable, and thus, he had to cop it.

I've looked around here, my biggest gripe is that alot of them are Series I, which are definitely not aesthetically, my cup of tea... furthermore, alot of cars here are modified quite a bit and/or thrashed.

Doesn't seem to be many M-Spec @ Carsales, but I'll keep looking.

heheh i had no problems with mine, when my compliance shop imported one. but anyways.. keep searching dude, im sure you will find one..

hmm another reason why its better 2 import is that you can buy a totally stock as a rock car and start fresh.. You just need to know the right ppl..

well gdluck anyhow..

lol, you say you dont want to import because of the odometer being wound back....where do you think all the 1's available locally came from?...they're all imports

if you dont mind a white car, then you should have no trouble finding 1....

lol, you say you dont want to import because of the odometer being wound back....where do you think all the 1's available locally came from?...they're all imports

if you dont mind a white car, then you should have no trouble finding 1....

Yeah, I realise that they're all imports, but irregardless I'd probably prefer a local one. However, looking at some of the import prices etc it'd probably be my best option.

Anyone interested in buying a Magna? :)

I would love a White Skyline, but I can't find any good nick Series II M-Spec for less than 20k. Quite strange, because some of them are really cheap too (some around 16k, but in automatic tranny and possibly something wrong?).

Mate when you’re talking about R33 GTS25-t M-Spec is implied, as they are the only specification released besides the A-LSD spec.

Edited by bigsully84
Mate when you’re talking about R33 GTS25-t M-Spec is implied, as they are the only specification released besides the A-LSD spec.

Really? So all, 1996 GTS-T 2.5's are M-Spec??? That'll help heaps.

Sorry to be a pain guys, I'm new to Skylines, I just they know they look sweet as, and go pretty hard.

Also... any idea on what needs to be done, and for how much with the major services?

I picked up a 95 series 1 with a genuine 48 000K's,, stock,, I also got a 3 inch pollished stainless Nismo exhaust with carbon fibre tip,, a new front mount,, a set of 17 inch Volks racing GTP's,, side skirts,, strut brace,, and a new stainless 3 inch high flow cat,,an extra front bar (dunno what type) a set of perfect series 2 front seats and got all that for 16.5 K,, got it from an importer over at moorooka Qld..

cheers

Edited by 33GTT

No true dude,, I am a mechanic and have worked in the rental car industry for years,, I can tell wear and tear, and this car is for real,, also under the bonnet is dusty and never washed,, it still has paper tags qith jap writing on the wiring harness,, it drives like new and feels the same,, I was very lucky

EDIT,, whoops, this reply went in the wrong possi,, forgive me I'm new,,

cheers

Edited by 33GTT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...