Jump to content
SAU Community

Nissan Cruise

DR1F7

By DR1F7,
in National Events

 Share

Recommended Posts

DR1F7 Apprentice

DR1F7

Posted
Posted (edited)

Full Details here incudling maps

Okay, So we have decided on the destination. And that is bribe Island

When: Sunday Nov 6th

Distances:

FROM: CITY CENTER BRISBANE Queensland

TO: CITY CENTER WOORIM Queensland

Total travel distance: 72.40 km

This cruise is for all makes of Nissan's (i guess we can include datsons too tongue.gif)

First meet: Coomera BP (Gold Coast)

9.00am for prompt 9.30am departure

Second meet: Springwood Maccas

9.55am for 10.20am departure

Then you will continue along the highway. Northbound. Making sure that you are to take the GATEWAY motorway exit…

Continue along the gateway… until you reach the tolls: note the tolls are $2.40 so please try and have change ready.

Third meet will be at BP Morayfield/Caboolutre…

(Continue along the GATEWAY motorway until you get to the GYMPIE ARTERIAL ROAD (Bald Hills)… You will then be on the BRUCE HIGHWAY… (Murrumba Downs) … If you continue along here… until you see the BIG BP on the left side of the road… turn off.. and regroup out the back… there is a rather large truck stop where everyone can meet.. just make sure there are no angry truckies hanging around.. cause sometimes they go hostile if you steal their parking bays!

Hopefully everyone should be here by 11.30ish…. and then we can continue on our to Bribie Island, dont miss the exit!

There are BBQ facalites, and activies to do there. As well as socalilising with each other.

Feel free to post if you are attending.

If you have any concerns, contact myself on boostcruising.com

Cheers

Lance

Edited by DR1F7
Link to comment
https://www.sau.com.au/forums/topic/89442-nissan-cruise/
Share on other sites
  • 4 years later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...