Jump to content
SAU Community

Recommended Posts

hey shan, with the light up panel factory option, is that a seperate rear bar altogether with the 'skyline' part cut out and the EL sheet behind it bla bla bla.. (I'm assuming it is).. or can I just get the light up part and stick it on the normal rear bar?

its not actually the reflectors, the globes need to be the coloured glass globes. if they are the clear globes with the rubber things over them thats when you can get defected. but thats not saying some cop wont defect you if you have the right globes in. but it is legal to have them with the correct globes.

hey shan, with the light up panel factory option, is that a seperate rear bar altogether with the 'skyline' part cut out and the EL sheet behind it bla bla bla.. (I'm assuming it is).. or can I just get the light up part and stick it on the normal rear bar?

its a piece that fits on top of a factory rear bumper.

its not actually the reflectors, the globes need to be the coloured glass globes. if they are the clear globes with the rubber things over them thats when you can get defected. but thats not saying some cop wont defect you if you have the right globes in. but it is legal to have them with the correct globes.

Yeah, the cop I saw defecting a car with Altezza lights said nothing about refelctors or anything. Didn't give a reason for defecting them, just basically said they are defective and don't argue.

Whereas a mechanic I know who does blue slips said as long as they are red on back etc. they are fine. Same goes for neons. But who is gunna have white neons on front, orange on sides and red on back? It'd look bloody stupid.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...