Jump to content
SAU Community

Recommended Posts

ill get back to ya with a time when im free mark, im a little busy this week but nothing that cant be sorted out ;)

Yeah I was thinking some nice freeway shots for you???

Should only take half an hour or so ;)

  • Replies 139
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Sorry Mick, fu<king whacked out day.

I'll let you know.

I did get MRR34 done, thats one down 11 to go.

I heard nothing last night??? (Just as well really, House 2hr special was on)

Weekend maybe???

ok i think to make it easier i might just miss out.

a couple of reasons. i now have stickers on the car so wont look as good for the calendar.

and im racing at the Powercruise StreetCar Shootout on Sat 6am-10pm

:D

and i know how hard it is for you to get everything together, so its okay.

mick

post-1794-1132193255.jpg

i'm available Friday night, from about 7:30 onwards, Saturday morning up until about 12, and Sunday afternoon after 4:30...

When would you like me, Mud?

(Car is covered in dirt/bugs/etc at the moment, so i gotta know when to wash it :P... already cleaned the engine bay though, so thats all good)

Done and Done.

see you at 4:15 at Shell Nudgee is fine

7:00 if its raining, but I doubt it will.

You still good for this Mud, I certainly am, 4:15am god damn that means up at 3:45am to get there :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...