Jump to content
SAU Community

Recommended Posts

hey how are u all goin?? my names kylie im 18 years of age.....and im a childcare worker!

5months ago i bought a R32 GTR 1989:) its all stock atm but when the money starts rolling in again it wil b getting work done to it! i would like to keep it as orginal as possible thought:P~

anyway im new to this site and thought i would say hello:)

hope to see u all around:):D

ill get a pic of my car up there very soon:)

Edited by ^MiSsY^
Link to comment
https://www.sau.com.au/forums/topic/92830-heyy/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

dont think that was me......maybe it was! hahahaha oh well keep looking out for me hahahaha!

oh yeah i think i saw that one at one of the mc tuning days! i have a blue r32 gtst and got bogged on the circuit that day i think  :D

Link to comment
https://www.sau.com.au/forums/topic/92830-heyy/#findComment-1676178
Share on other sites

oh yeah i think i saw that one at one of the mc tuning days! i have a blue r32 gtst and got bogged on the circuit that day i think  :D

Was it the september tuning arvo? I have a dark blue R32 GTR and I was there....But I don't remember there being any 32 gts-t's :(

Yeah Missy I understand you're position, I have an office job and it's not easy owning a GTR on that kind of money!!! Then again I am a little bit older than you so the pay probably isn't quite so lousy (21) Takes forever to save up whenever I need money for the car though :)

Link to comment
https://www.sau.com.au/forums/topic/92830-heyy/#findComment-1676357
Share on other sites




  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...